Eaton FP1208R1-R25-R High Current Inductor, 250 nH 0.29 mOhm
Eaton FP1208R1-R25-R High Current Inductor, 250 nH 0.29 mOhm

Eaton FP1208R1-R25-R High Current Inductor, 250 nH 0.29 mOhm

Share
pEaton FP1208R1-R25-R: 250 nH high frequency, high current power inductor, 50 A Irms, 55 A Isat, DCR 0.29 mOhm, 12.0 x 8.0 mm package./p
    • Product Details
    • Download

    FP1208R1-R25-R at a glance: 250 nH high frequency, high current power inductor, 50 A Irms, 55 A Isat, DCR 0.29 mOhm, 12.0 x 8.0 mm body, 8.0 mm tall.

    Eaton FP1208R1-R25-R High frequency, high current power inductors

    FP1208R1-R25-R is one of Eaton's high frequency, high current power inductor series, 12.0 x 8.0 mm with a 8.0 mm tall profile. Electrically it offers 250 nH at 50 A Irms and 0.29 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Specification Table

    Orderable part numberFP1208R1-R25-R
    Inductance, OCL (0 Adc)250 nH
    Inductance, FLL (minimum)191 nH
    Irms (40 °C rise, no core loss)50 A
    Isat (20% roll-off @ +25 °C)55 A
    Isat2 (20% roll-off @ +85 °C)48 A
    Isat3 (20% roll-off @ +125 °C)44 A
    DCR typical @ +20 °C0.29 mOhm
    K-factor (Bp-p = K x L x dI)283
    Package12.0 x 8.0 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    Two inductance figures are published. 250 nH is measured with no DC in the winding, 191 nH with the winding loaded to Isat1. The gap between them is 24%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Peak current at 20% roll-off is 55 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    The 725 mW dissipated at 50 A through 0.29 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Flux swing follows Bp-p = K x L x dI. With K = 283 and a ripple of 16.5 A the core sees roughly 116.7 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    What This Family Is For

    At 12.0 x 8.0 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 250 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it the highest inductance of the 5 parts in this data sheet.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    The order of checks that works: compute ripple from 250 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.29 mOhm the winding is not the loss, the trace can be.

    Outline Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1208R1-R25-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message