Eaton FP1308-R21-R 210 nH 72 A Saturation Inductor
Eaton FP1308-R21-R 210 nH 72 A Saturation Inductor

Eaton FP1308-R21-R 210 nH 72 A Saturation Inductor

Share
pEaton FP1308-R21-R: 210 nH high frequency, high current power inductor, 68 A Irms, 72 A Isat, DCR 0.2 mOhm, 13.7 x 12.9 mm package./p
    • Product Details
    • Download

    FP1308-R21-R at a glance: 210 nH high frequency, high current power inductor, 68 A Irms, 72 A Isat, DCR 0.2 mOhm, 13.7 x 12.9 mm body, 8.0 mm tall.

    Eaton FP1308-R21-R High frequency, high current power inductors

    FP1308-R21-R is one of Eaton's high frequency, high current power inductor series, 13.7 x 12.9 mm with a 8.0 mm tall profile. Electrically it offers 210 nH at 68 A Irms and 0.2 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Specification Table

    Orderable part numberFP1308-R21-R
    Inductance, OCL (0 Adc)210 nH
    Irms (40 °C rise, no core loss)68 A
    Isat (20% roll-off @ +25 °C)72 A
    DCR typical @ +20 °C0.2 mOhm
    DCR maximum @ +20 °C0.24 mOhm
    K-factor (Bp-p = K x L x dI)21.3
    Package13.7 x 12.9 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    210 nH is the unbiased inductance. The data sheet does not publish a separate full-load figure for this part, so leave margin when you compute ripple at rated current.

    Peak current at 20% roll-off is 72 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    The 925 mW dissipated at 68 A through 0.2 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Flux swing follows Bp-p = K x L x dI. With K = 21.3 and a ripple of 21.6 A the core sees roughly 9.7 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Series Positioning

    At 13.7 x 12.9 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 210 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 2 of 5 when the data sheet is sorted by inductance.

    • Application fit: Voltage regulator modules (VRMs) for servers and microprocessors, Multi-phase buck inductors, High frequency, high current switching power supplies.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 210 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.2 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Outline Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1308-R21-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products