Eaton FP1308R1-R21-R 210 nH 80 A Saturation Inductor
Eaton FP1308R1-R21-R 210 nH 80 A Saturation Inductor

Eaton FP1308R1-R21-R 210 nH 80 A Saturation Inductor

Share
pEaton FP1308R1-R21-R: 210 nH high frequency, high current power inductor, 57 A Irms, 80 A Isat, DCR 0.32 mOhm, 13.4 x 12.7 mm package./p
    • Product Details
    • Download

    FP1308R1-R21-R at a glance: 210 nH high frequency, high current power inductor, 57 A Irms, 80 A Isat, DCR 0.32 mOhm, 13.4 x 12.7 mm body, 8.0 mm tall.

    Eaton FP1308R1-R21-R High frequency, high current power inductors

    FP1308R1-R21-R is one of Eaton's high frequency, high current power inductor series, 13.4 x 12.7 mm with a 8.0 mm tall profile. Electrically it offers 210 nH at 57 A Irms and 0.32 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Specification Table

    Orderable part numberFP1308R1-R21-R
    Inductance, OCL (0 Adc)210 nH
    Inductance, FLL (minimum)152 nH
    Irms (40 °C rise, no core loss)57 A
    Isat (20% roll-off @ +25 °C)80 A
    Isat2 (20% roll-off @ +125 °C)68 A
    DCR typical @ +20 °C0.32 mOhm
    K-factor (Bp-p = K x L x dI)233
    Package13.4 x 12.7 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    210 nH open-circuit, 152 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    The first Isat column, 80 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    The 1040 mW dissipated at 57 A through 0.32 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Core loss needs flux, and flux here is about 117.4 mT for a 24 A ripple (K = 233). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    What This Family Is For

    At 13.4 x 12.7 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 210 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 4 of 15 when the data sheet is sorted by inductance, DCR sits between the 0.18 and 0.53 mOhm the series covers.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 210 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.32 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1308R1-R21-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message