
FP1308R1-R26-R at a glance: 260 nH high frequency, high current power inductor, 57 A Irms, 64 A Isat, DCR 0.32 mOhm, 13.4 x 12.7 mm body, 8.0 mm tall.
FP1308R1-R26-R is one of Eaton's high frequency, high current power inductor series, 13.4 x 12.7 mm with a 8.0 mm tall profile. Electrically it offers 260 nH at 57 A Irms and 0.32 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.
| Orderable part number | FP1308R1-R26-R |
| Inductance, OCL (0 Adc) | 260 nH |
| Inductance, FLL (minimum) | 187 nH |
| Irms (40 °C rise, no core loss) | 57 A |
| Isat (20% roll-off @ +25 °C) | 64 A |
| Isat2 (20% roll-off @ +125 °C) | 52 A |
| DCR typical @ +20 °C | 0.32 mOhm |
| K-factor (Bp-p = K x L x dI) | 233 |
| Package | 13.4 x 12.7 mm, 8.0 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
At zero bias the winding measures 260 nH. Put Isat1 through it and the figure falls to 187 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 260 nH number; loop stability and worst-case current belong on the lower one.
The first Isat column, 64 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.
Irms of 57 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.32 mOhm that is roughly 1040 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.
The K-factor of 233 turns ripple into flux: a peak-to-peak swing of 19.2 A gives about 116.3 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.
At 13.4 x 12.7 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 260 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.
That makes it part 7 of 15 when the data sheet is sorted by inductance, DCR sits between the 0.18 and 0.53 mOhm the series covers.
The order of checks that works: compute ripple from 260 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.
Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.32 mOhm the winding is not the loss, the trace can be.
Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

How is the part packed?
Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.
Is this part AEC-Q200 qualified?
No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd