Eaton FP1308R1-R44-R High Current Inductor, 440 nH 0.32 mOhm
Eaton FP1308R1-R44-R High Current Inductor, 440 nH 0.32 mOhm

Eaton FP1308R1-R44-R High Current Inductor, 440 nH 0.32 mOhm

Share
pEaton FP1308R1-R44-R: 440 nH high frequency, high current power inductor, 57 A Irms, 37 A Isat, DCR 0.32 mOhm, 13.4 x 12.7 mm package./p
    • Product Details
    • Download

    FP1308R1-R44-R at a glance: 440 nH high frequency, high current power inductor, 57 A Irms, 37 A Isat, DCR 0.32 mOhm, 13.4 x 12.7 mm body, 8.0 mm tall.

    Eaton FP1308R1-R44-R High frequency, high current power inductors

    Eaton builds the FP1308R1-R44-R as a high frequency, high current power inductor for 13.4 x 12.7 mm footprints. At 440 nH and 57 A Irms with 0.32 mOhm of DCR it targets high-current DC-DC stages; the 8.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Specification Table

    Orderable part numberFP1308R1-R44-R
    Inductance, OCL (0 Adc)440 nH
    Inductance, FLL (minimum)317 nH
    Irms (40 °C rise, no core loss)57 A
    Isat (20% roll-off @ +25 °C)37 A
    Isat2 (20% roll-off @ +125 °C)28 A
    DCR typical @ +20 °C0.32 mOhm
    K-factor (Bp-p = K x L x dI)233
    Package13.4 x 12.7 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    440 nH open-circuit, 317 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    The first Isat column, 37 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Copper loss at the rated current works out at about 1040 mW (57 A squared times 0.32 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Core loss needs flux, and flux here is about 113.8 mT for a 11.1 A ripple (K = 233). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Where This Part Sits in the Range

    At 13.4 x 12.7 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 440 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 13 of 15 when the data sheet is sorted by inductance, DCR sits between the 0.18 and 0.53 mOhm the series covers.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 440 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.32 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1308R1-R44-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products