Eaton FP1308R2-R11-R 45 A SMD Power Inductor, 110 nH
Eaton FP1308R2-R11-R 45 A SMD Power Inductor, 110 nH

Eaton FP1308R2-R11-R 45 A SMD Power Inductor, 110 nH

Share
pEaton FP1308R2-R11-R: 110 nH high frequency, high current power inductor, 45 A Irms, 120 A Isat, DCR 0.53 mOhm, 13.4 x 12.7 mm package./p
    • Product Details
    • Download

    FP1308R2-R11-R at a glance: 110 nH high frequency, high current power inductor, 45 A Irms, 120 A Isat, DCR 0.53 mOhm, 13.4 x 12.7 mm body, 8.0 mm tall.

    Eaton FP1308R2-R11-R High frequency, high current power inductors

    Eaton builds the FP1308R2-R11-R as a high frequency, high current power inductor for 13.4 x 12.7 mm footprints. At 110 nH and 45 A Irms with 0.53 mOhm of DCR it targets high-current DC-DC stages; the 8.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Ratings at a Glance

    Orderable part numberFP1308R2-R11-R
    Inductance, OCL (0 Adc)110 nH
    Inductance, FLL (minimum)79 nH
    Irms (40 °C rise, no core loss)45 A
    Isat (20% roll-off @ +25 °C)120 A
    Isat2 (20% roll-off @ +125 °C)105 A
    DCR typical @ +20 °C0.53 mOhm
    K-factor (Bp-p = K x L x dI)233
    Package13.4 x 12.7 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    At zero bias the winding measures 110 nH. Put Isat1 through it and the figure falls to 79 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 110 nH number; loop stability and worst-case current belong on the lower one.

    The first Isat column, 120 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Copper loss at the rated current works out at about 1073 mW (45 A squared times 0.53 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Flux swing follows Bp-p = K x L x dI. With K = 233 and a ripple of 36 A the core sees roughly 92.3 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Series Positioning

    At 13.4 x 12.7 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 110 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it the lowest inductance of the 15 parts in this data sheet, with the highest DCR in the series at 0.53 mOhm, which is what the extra turns cost, Irms of 45 A is the bottom of the family.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Size the inductor on peak current first, not average. With 110 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    On the board, place the part so the switch-node copper is short and wide. At 0.53 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1308R2-R11-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products