Eaton FP1308R3-R32-R - 320 nH Shielded Power Inductor 13.4 x 12.7 mm
Eaton FP1308R3-R32-R - 320 nH Shielded Power Inductor 13.4 x 12.7 mm

Eaton FP1308R3-R32-R - 320 nH Shielded Power Inductor 13.4 x 12.7 mm

Share
pEaton FP1308R3-R32-R: 320 nH high frequency, high current power inductor, 68 A Irms, 52 A Isat, DCR 0.18 mOhm, 13.4 x 12.7 mm package./p
    • Product Details
    • Download

    FP1308R3-R32-R at a glance: 320 nH high frequency, high current power inductor, 68 A Irms, 52 A Isat, DCR 0.18 mOhm, 13.4 x 12.7 mm body, 8.0 mm tall.

    Eaton FP1308R3-R32-R High frequency, high current power inductors

    The FP1308R3-R32-R is a 13.4 x 12.7 mm high frequency, high current power inductor from Eaton, rated 68 A Irms at 320 nH and 0.18 mOhm typical DCR. It is a surface-mount part 8.0 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Specification Table

    Orderable part numberFP1308R3-R32-R
    Inductance, OCL (0 Adc)320 nH
    Inductance, FLL (minimum)230 nH
    Irms (40 °C rise, no core loss)68 A
    Isat (20% roll-off @ +25 °C)52 A
    Isat2 (20% roll-off @ +125 °C)40 A
    DCR typical @ +20 °C0.18 mOhm
    K-factor (Bp-p = K x L x dI)233
    Package13.4 x 12.7 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    320 nH open-circuit, 230 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Saturation is quoted as 20% roll-off at 52 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    The 832 mW dissipated at 68 A through 0.18 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    The K-factor of 233 turns ripple into flux: a peak-to-peak swing of 15.6 A gives about 116.3 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    What This Family Is For

    At 13.4 x 12.7 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 320 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 10 of 15 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.18 mOhm, Irms of 68 A is the top of the family.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    The order of checks that works: compute ripple from 320 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    On the board, place the part so the switch-node copper is short and wide. At 0.18 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1308R3-R32-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message