
FP1309B1-R150-R at a glance: 150 nH high frequency, high current power inductor, 60 A Irms, 80 A Isat, DCR 0.19 mOhm, 12.8 x 8.3 mm body, 8.8 mm tall.
Eaton FP1309B1-R150-R is a high frequency, high current power inductor in a 12.8 x 8.3 mm surface-mount package. It carries 150 nH of open-circuit inductance with 60 A Irms and a typical DCR of 0.19 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 8.8 mm tall and rated from -40 °C to +125 °C.
| Orderable part number | FP1309B1-R150-R |
| Inductance, OCL (0 Adc) | 150 nH |
| Inductance, FLL (minimum) | 108 nH |
| Irms (40 °C rise, no core loss) | 60 A |
| Isat (20% roll-off @ +25 °C) | 80 A |
| Isat2 (20% roll-off @ +125 °C) | 64 A |
| DCR typical @ +20 °C | 0.19 mOhm |
| K-factor (Bp-p = K x L x dI) | 296 |
| Package | 12.8 x 8.3 mm, 8.8 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
At zero bias the winding measures 150 nH. Put Isat1 through it and the figure falls to 108 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 150 nH number; loop stability and worst-case current belong on the lower one.
Peak current at 20% roll-off is 80 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.
The 684 mW dissipated at 60 A through 0.19 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.
Flux swing follows Bp-p = K x L x dI. With K = 296 and a ripple of 24 A the core sees roughly 106.6 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.
At 12.8 x 8.3 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 150 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.
That makes it the highest inductance of the 3 parts in this data sheet.
Size the inductor on peak current first, not average. With 150 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.
Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.19 mOhm the winding is not the loss, the trace can be.
Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

How is the part packed?
Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.
Is this part AEC-Q200 qualified?
No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd