Eaton FP1505R1-R25-R 250 nH 42 A Saturation Inductor
Eaton FP1505R1-R25-R 250 nH 42 A Saturation Inductor

Eaton FP1505R1-R25-R 250 nH 42 A Saturation Inductor

Share
pEaton FP1505R1-R25-R: 250 nH high frequency, high current power inductor, 53 A Irms, 42 A Isat, DCR 0.47 mOhm, 7.0 x 15.0 mm package./p
    • Product Details
    • Download

    FP1505R1-R25-R at a glance: 250 nH high frequency, high current power inductor, 53 A Irms, 42 A Isat, DCR 0.47 mOhm, 7.0 x 15.0 mm body, 5.0 mm tall.

    Eaton FP1505R1-R25-R High frequency, high current power inductors

    Eaton FP1505R1-R25-R is a high frequency, high current power inductor in a 7.0 x 15.0 mm surface-mount package. It carries 250 nH of open-circuit inductance with 53 A Irms and a typical DCR of 0.47 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 5.0 mm tall and rated from -40 °C to +125 °C.

    Key Specifications

    Orderable part numberFP1505R1-R25-R
    Inductance, OCL (0 Adc)250 nH
    Inductance, FLL (minimum)180 nH
    Irms (40 °C rise, no core loss)53 A
    Isat (20% roll-off @ +25 °C)42 A
    Isat2 (20% roll-off @ +125 °C)32 A
    DCR typical @ +20 °C0.47 mOhm
    K-factor (Bp-p = K x L x dI)356.3
    Package7.0 x 15.0 mm, 5.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    At zero bias the winding measures 250 nH. Put Isat1 through it and the figure falls to 180 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 250 nH number; loop stability and worst-case current belong on the lower one.

    Peak current at 20% roll-off is 42 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Irms of 53 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.47 mOhm that is roughly 1320 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Core loss needs flux, and flux here is about 112.2 mT for a 12.6 A ripple (K = 356.3). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Where This Part Sits in the Range

    At 7.0 x 15.0 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 250 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 4 of 6 when the data sheet is sorted by inductance.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    The order of checks that works: compute ripple from 250 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.47 mOhm the winding is not the loss, the trace can be.

    Mechanical Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1505R1-R25-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products