Eaton FP2-D047-R 37 A SMD Power Inductor, 47 nH
Eaton FP2-D047-R 37 A SMD Power Inductor, 47 nH

Eaton FP2-D047-R 37 A SMD Power Inductor, 47 nH

Share
pEaton FP2-D047-R: 47 nH high current power inductor, 37 A Irms, 42 A Isat, DCR 0.26 mOhm, 7.2 x 6.7 mm package./p
    • Product Details
    • Download

    FP2-D047-R at a glance: 47 nH high current power inductor, 37 A Irms, 42 A Isat, DCR 0.26 mOhm, 7.2 x 6.7 mm body, 3.0 mm or 5.0 mm tall.

    Eaton FP2-D047-R High current power inductors

    The FP2-D047-R is a 7.2 x 6.7 mm high current power inductor from Eaton, rated 37 A Irms at 47 nH and 0.26 mOhm typical DCR. It is a surface-mount part 3.0 mm or 5.0 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Specification Table

    Orderable part numberFP2-D047-R
    Inductance, OCL (0 Adc)47 nH
    Irms (40 °C rise, no core loss)37 A
    Isat (30% roll-off @ +20 °C)42 A
    DCR typical @ +20 °C0.26 mOhm
    Volt-microsecond rating0.75 V-us
    Package7.2 x 6.7 mm, 3.0 mm / 5.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)
    Windings in seriessecond connection mode, same part
      Inductance, OCL188 nH
      Irms16 A
      Isat21 A
      DCR typical @ +20 °C1.3 mOhm

    The Figures Explained

    Only the open-circuit value, 47 nH, is tabulated here. With DC in the winding the core will show less, so treat 47 nH as a ceiling rather than an operating value.

    Saturation is quoted as 30% roll-off at 42 A at +20 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Irms of 37 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.26 mOhm that is roughly 356 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.

    Positioning in the FP Range

    This is one of the smaller bodies in the FP range. At 7.2 x 6.7 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 47 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it the lowest inductance of the 15 parts in this data sheet, DCR sits between the 0.24 and 0.28 mOhm the series covers, Irms of 37 A is the bottom of the family.

    • Application fit: Servers, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    The order of checks that works: compute ripple from 47 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.26 mOhm the winding is not the loss, the trace can be.

    Mechanical Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP2-D047-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products