Eaton FP2-D100-R - 100 nH Shielded Power Inductor 7.2 x 6.7 mm
Eaton FP2-D100-R - 100 nH Shielded Power Inductor 7.2 x 6.7 mm

Eaton FP2-D100-R - 100 nH Shielded Power Inductor 7.2 x 6.7 mm

Share
pEaton FP2-D100-R: 100 nH high current power inductor, 37 A Irms, 22 A Isat, DCR 0.26 mOhm, 7.2 x 6.7 mm package./p
    • Product Details
    • Download

    FP2-D100-R at a glance: 100 nH high current power inductor, 37 A Irms, 22 A Isat, DCR 0.26 mOhm, 7.2 x 6.7 mm body, 3.0 mm or 5.0 mm tall.

    Eaton FP2-D100-R High current power inductors

    Eaton builds the FP2-D100-R as a high current power inductor for 7.2 x 6.7 mm footprints. At 100 nH and 37 A Irms with 0.26 mOhm of DCR it targets high-current DC-DC stages; the 3.0 mm or 5.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Electrical Specifications

    Orderable part numberFP2-D100-R
    Inductance, OCL (0 Adc)100 nH
    Irms (40 °C rise, no core loss)37 A
    Isat (30% roll-off @ +20 °C)22 A
    DCR typical @ +20 °C0.26 mOhm
    Volt-microsecond rating0.75 V-us
    Package7.2 x 6.7 mm, 3.0 mm / 5.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)
    Windings in seriessecond connection mode, same part
      Inductance, OCL400 nH
      Irms16 A
      Isat11 A
      DCR typical @ +20 °C1.3 mOhm

    Reading the Data Sheet

    Only the open-circuit value, 100 nH, is tabulated here. With DC in the winding the core will show less, so treat 100 nH as a ceiling rather than an operating value.

    Saturation is quoted as 30% roll-off at 22 A at +20 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Copper loss at the rated current works out at about 356 mW (37 A squared times 0.26 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.

    What This Family Is For

    This is one of the smaller bodies in the FP range. At 7.2 x 6.7 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 100 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it part 8 of 15 when the data sheet is sorted by inductance, DCR sits between the 0.24 and 0.28 mOhm the series covers, Irms of 37 A is the bottom of the family.

    • Application fit: Servers, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    The order of checks that works: compute ripple from 100 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.26 mOhm the winding is not the loss, the trace can be.

    Mechanical Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP2-D100-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products