Eaton FP2-D120-R High Current Inductor, 120 nH 0.26 mOhm
Eaton FP2-D120-R High Current Inductor, 120 nH 0.26 mOhm

Eaton FP2-D120-R High Current Inductor, 120 nH 0.26 mOhm

Share
pEaton FP2-D120-R: 120 nH high current power inductor, 37 A Irms, 18 A Isat, DCR 0.26 mOhm, 7.2 x 6.7 mm package./p
    • Product Details
    • Download

    FP2-D120-R at a glance: 120 nH high current power inductor, 37 A Irms, 18 A Isat, DCR 0.26 mOhm, 7.2 x 6.7 mm body, 3.0 mm or 5.0 mm tall.

    Eaton FP2-D120-R High current power inductors

    The FP2-D120-R is a 7.2 x 6.7 mm high current power inductor from Eaton, rated 37 A Irms at 120 nH and 0.26 mOhm typical DCR. It is a surface-mount part 3.0 mm or 5.0 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Electrical Specifications

    Orderable part numberFP2-D120-R
    Inductance, OCL (0 Adc)120 nH
    Irms (40 °C rise, no core loss)37 A
    Isat (30% roll-off @ +20 °C)18 A
    DCR typical @ +20 °C0.26 mOhm
    Volt-microsecond rating0.75 V-us
    Package7.2 x 6.7 mm, 3.0 mm / 5.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)
    Windings in seriessecond connection mode, same part
      Inductance, OCL480 nH
      Irms16 A
      Isat9 A
      DCR typical @ +20 °C1.3 mOhm

    The Figures Explained

    Only the open-circuit value, 120 nH, is tabulated here. With DC in the winding the core will show less, so treat 120 nH as a ceiling rather than an operating value.

    The first Isat column, 18 A at +20 °C, is the peak the part takes at 30% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Copper loss at the rated current works out at about 356 mW (37 A squared times 0.26 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.

    Positioning in the FP Range

    This is one of the smaller bodies in the FP range. At 7.2 x 6.7 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 120 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 11 of 15 when the data sheet is sorted by inductance, DCR sits between the 0.24 and 0.28 mOhm the series covers, Irms of 37 A is the bottom of the family.

    • Application fit: Servers, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 120 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.26 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP2-D120-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products