Eaton FP2-S047-R 39 A SMD Power Inductor, 47 nH
Eaton FP2-S047-R 39 A SMD Power Inductor, 47 nH

Eaton FP2-S047-R 39 A SMD Power Inductor, 47 nH

Share
pEaton FP2-S047-R: 47 nH high current power inductor, 39 A Irms, 42 A Isat, DCR 0.24 mOhm, 7.2 x 6.7 mm package./p
    • Product Details
    • Download

    FP2-S047-R at a glance: 47 nH high current power inductor, 39 A Irms, 42 A Isat, DCR 0.24 mOhm, 7.2 x 6.7 mm body, 3.0 mm or 5.0 mm tall.

    Eaton FP2-S047-R High current power inductors

    Eaton builds the FP2-S047-R as a high current power inductor for 7.2 x 6.7 mm footprints. At 47 nH and 39 A Irms with 0.24 mOhm of DCR it targets high-current DC-DC stages; the 3.0 mm or 5.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Electrical Specifications

    Orderable part numberFP2-S047-R
    Inductance, OCL (0 Adc)47 nH
    Irms (40 °C rise, no core loss)39 A
    Isat (30% roll-off @ +20 °C)42 A
    DCR typical @ +20 °C0.24 mOhm
    Volt-microsecond rating0.75 V-us
    Package7.2 x 6.7 mm, 3.0 mm / 5.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    47 nH is the unbiased inductance. The data sheet does not publish a separate full-load figure for this part, so leave margin when you compute ripple at rated current.

    Saturation is quoted as 30% roll-off at 42 A at +20 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Copper loss at the rated current works out at about 365 mW (39 A squared times 0.24 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.

    What This Family Is For

    This is one of the smaller bodies in the FP range. At 7.2 x 6.7 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 47 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it the lowest inductance of the 15 parts in this data sheet, and it shares the lowest DCR here at 0.24 mOhm, Irms of 39 A is the top of the family.

    • Application fit: Servers, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Size the inductor on peak current first, not average. With 47 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    On the board, place the part so the switch-node copper is short and wide. At 0.24 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Outline Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP2-S047-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products