
FP2-S082-R at a glance: 82 nH high current power inductor, 39 A Irms, 26 A Isat, DCR 0.24 mOhm, 7.2 x 6.7 mm body, 3.0 mm or 5.0 mm tall.
The FP2-S082-R is a 7.2 x 6.7 mm high current power inductor from Eaton, rated 39 A Irms at 82 nH and 0.24 mOhm typical DCR. It is a surface-mount part 3.0 mm or 5.0 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.
| Orderable part number | FP2-S082-R |
| Inductance, OCL (0 Adc) | 82 nH |
| Irms (40 °C rise, no core loss) | 39 A |
| Isat (30% roll-off @ +20 °C) | 26 A |
| DCR typical @ +20 °C | 0.24 mOhm |
| Volt-microsecond rating | 0.75 V-us |
| Package | 7.2 x 6.7 mm, 3.0 mm / 5.0 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
82 nH is the unbiased inductance. The data sheet does not publish a separate full-load figure for this part, so leave margin when you compute ripple at rated current.
Peak current at 30% roll-off is 26 A at +20 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.
Copper loss at the rated current works out at about 365 mW (39 A squared times 0.24 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.
The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.
This is one of the smaller bodies in the FP range. At 7.2 x 6.7 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 82 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.
That makes it part 6 of 15 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.24 mOhm, Irms of 39 A is the top of the family.
The order of checks that works: compute ripple from 82 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.
On the board, place the part so the switch-node copper is short and wide. At 0.24 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.
The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

Is this part AEC-Q200 qualified?
No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.
How is the part packed?
Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd