Eaton FP2-V150-R High Current Inductor, 150 nH 0.28 mOhm
Eaton FP2-V150-R High Current Inductor, 150 nH 0.28 mOhm

Eaton FP2-V150-R High Current Inductor, 150 nH 0.28 mOhm

Share
pEaton FP2-V150-R: 150 nH high current power inductor, 37 A Irms, 25.5 A Isat, DCR 0.28 mOhm, 7.2 x 6.7 mm package./p
    • Product Details
    • Download

    FP2-V150-R at a glance: 150 nH high current power inductor, 37 A Irms, 25.5 A Isat, DCR 0.28 mOhm, 7.2 x 6.7 mm body, 3.0 mm or 5.0 mm tall.

    Eaton FP2-V150-R High current power inductors

    Eaton builds the FP2-V150-R as a high current power inductor for 7.2 x 6.7 mm footprints. At 150 nH and 37 A Irms with 0.28 mOhm of DCR it targets high-current DC-DC stages; the 3.0 mm or 5.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Electrical Specifications

    Orderable part numberFP2-V150-R
    Inductance, OCL (0 Adc)150 nH
    Irms (40 °C rise, no core loss)37 A
    Isat (30% roll-off @ +20 °C)25.5 A
    DCR typical @ +20 °C0.28 mOhm
    Volt-microsecond rating0.99 V-us
    Package7.2 x 6.7 mm, 3.0 mm / 5.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    Only the open-circuit value, 150 nH, is tabulated here. With DC in the winding the core will show less, so treat 150 nH as a ceiling rather than an operating value.

    The first Isat column, 25.5 A at +20 °C, is the peak the part takes at 30% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Irms of 37 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.28 mOhm that is roughly 383 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.

    Series Positioning

    This is one of the smaller bodies in the FP range. At 7.2 x 6.7 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 150 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 14 of 15 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.28 mOhm, which is what the extra turns cost, Irms of 37 A is the bottom of the family.

    • Application fit: Servers, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 150 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.28 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Outline Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP2-V150-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message