Eaton FP2207R1-R230-R 50 A SMD Power Inductor, 230 nH
Eaton FP2207R1-R230-R 50 A SMD Power Inductor, 230 nH

Eaton FP2207R1-R230-R 50 A SMD Power Inductor, 230 nH

Share
pEaton FP2207R1-R230-R: 230 nH high frequency, high current power inductor, 50 A Irms, 70 A Isat, DCR 0.47 mOhm, 22.5 x 8.2 mm package./p
    • Product Details
    • Download

    FP2207R1-R230-R at a glance: 230 nH high frequency, high current power inductor, 50 A Irms, 70 A Isat, DCR 0.47 mOhm, 22.5 x 8.2 mm body, 7.25 mm tall.

    Eaton FP2207R1-R230-R High frequency, high current power inductors

    FP2207R1-R230-R is one of Eaton's high frequency, high current power inductor series, 22.5 x 8.2 mm with a 7.25 mm tall profile. Electrically it offers 230 nH at 50 A Irms and 0.47 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Ratings at a Glance

    Orderable part numberFP2207R1-R230-R
    Inductance, OCL (0 Adc)230 nH
    Inductance, FLL (minimum)196 nH
    Irms (40 °C rise, no core loss)50 A
    Isat (5% roll-off @ +25 °C)70 A
    Isat2 (20% roll-off @ +100 °C)77 A
    Isat3 (20% roll-off @ +125 °C)72 A
    DCR typical @ +20 °C0.47 mOhm
    K-factor (Bp-p = K x L x dI)182.5
    Package22.5 x 8.2 mm, 7.25 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-55 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    Two inductance figures are published. 230 nH is measured with no DC in the winding, 196 nH with the winding loaded to Isat1. The gap between them is 15%, and it is the reason a converter that looks well damped at no load can ring at full current.

    The first Isat column, 70 A at +25 °C, is the peak the part takes at 5% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    The 1175 mW dissipated at 50 A through 0.47 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    The K-factor of 182.5 turns ripple into flux: a peak-to-peak swing of 21 A gives about 88.1 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Series Positioning

    This is one of the smaller bodies in the FP range. At 22.5 x 8.2 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 230 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs) and high- power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -55 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Size the inductor on peak current first, not average. With 230 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.47 mOhm the winding is not the loss, the trace can be.

    Mechanical Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP2207R1-R230-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products