Eaton FP3-100-R 10.9 uH 2.3 A Saturation Inductor
Eaton FP3-100-R 10.9 uH 2.3 A Saturation Inductor

Eaton FP3-100-R 10.9 uH 2.3 A Saturation Inductor

Share
pEaton FP3-100-R: 10.9 uH high current, low profile inductor, 2.3 A Irms, 2.3 A Isat, DCR 84.2 mOhm, 7.25 x 6.7 mm package./p
    • Product Details
    • Download

    FP3-100-R at a glance: 10.9 uH high current, low profile inductor, 2.3 A Irms, 2.3 A Isat, DCR 84.2 mOhm, 7.25 x 6.7 mm body, 3.0 mm tall.

    Eaton FP3-100-R High current, low profile inductors

    Eaton builds the FP3-100-R as a high current, low profile inductor for 7.25 x 6.7 mm footprints. At 10.9 uH and 2.3 A Irms with 84.2 mOhm of DCR it targets high-current DC-DC stages; the 3.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +155 °C.

    Key Specifications

    Orderable part numberFP3-100-R
    Inductance, OCL (0 Adc)10.9 uH
    Irms (40 °C rise, no core loss)2.3 A
    Isat2.3 A
    Isat23 A
    DCR typical @ +20 °C84.2 mOhm
    DCR maximum @ +20 °C101 mOhm
    K-factor (Bp-p = K x L x dI)69
    Package7.25 x 6.7 mm, 3.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +155 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    Only the open-circuit value, 10.9 uH, is tabulated here. With DC in the winding the core will show less, so treat 10.9 uH as a ceiling rather than an operating value.

    Peak current at the quoted roll-off is 2.3 A. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Copper loss at the rated current works out at about 445 mW (2.3 A squared times 84.2 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Core loss needs flux, and flux here is about 51.9 mT for a 0.69 A ripple (K = 69). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Positioning in the FP Range

    This is one of the smaller bodies in the FP range. At 7.25 x 6.7 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 10.9 uH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 11 of 12 when the data sheet is sorted by inductance, DCR sits between the 1 and 106 mOhm the series covers.

    • Application fit: Voltage Regulator Modules (VRMs), Multi-phase regulators, Desktop and server VRMs and EVRDs.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +155 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    Size the inductor on peak current first, not average. With 10.9 uH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 84.2 mOhm the winding is not the loss, the trace can be.

    Outline Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP3-100-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products