
FP3-150-R at a glance: 14.9 uH high current, low profile inductor, 2.22 A Irms, 2 A Isat, DCR 106 mOhm, 7.25 x 6.7 mm body, 3.0 mm tall.
FP3-150-R is one of Eaton's high current, low profile inductor series, 7.25 x 6.7 mm with a 3.0 mm tall profile. Electrically it offers 14.9 uH at 2.22 A Irms and 106 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.
| Orderable part number | FP3-150-R |
| Inductance, OCL (0 Adc) | 14.9 uH |
| Irms (40 °C rise, no core loss) | 2.22 A |
| Isat | 2 A |
| Isat2 | 2.5 A |
| DCR typical @ +20 °C | 106 mOhm |
| DCR maximum @ +20 °C | 127 mOhm |
| K-factor (Bp-p = K x L x dI) | 59 |
| Package | 7.25 x 6.7 mm, 3.0 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +155 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
14.9 uH is the unbiased inductance. The data sheet does not publish a separate full-load figure for this part, so leave margin when you compute ripple at rated current.
Peak current at the quoted roll-off is 2 A. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.
Irms of 2.22 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 106 mOhm that is roughly 522 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.
Core loss needs flux, and flux here is about 52.7 mT for a 0.6 A ripple (K = 59). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.
This is one of the smaller bodies in the FP range. At 7.25 x 6.7 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 14.9 uH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.
That makes it the highest inductance of the 12 parts in this data sheet, with the highest DCR in the series at 106 mOhm, which is what the extra turns cost, Irms of 2.22 A is the bottom of the family.
Size the inductor on peak current first, not average. With 14.9 uH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.
Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 106 mOhm the winding is not the loss, the trace can be.
The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

Can I substitute a lower inductance in the same body?
Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.
How is the part packed?
Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd