Eaton FP3-1R5-R High Current Inductor, 1.5 uH 10 mOhm
Eaton FP3-1R5-R High Current Inductor, 1.5 uH 10 mOhm

Eaton FP3-1R5-R High Current Inductor, 1.5 uH 10 mOhm

Share
pEaton FP3-1R5-R: 1.5 uH high current, low profile inductor, 5.78 A Irms, 6.2 A Isat, DCR 10 mOhm, 7.25 x 6.7 mm package./p
    • Product Details
    • Download

    FP3-1R5-R at a glance: 1.5 uH high current, low profile inductor, 5.78 A Irms, 6.2 A Isat, DCR 10 mOhm, 7.25 x 6.7 mm body, 3.0 mm tall.

    Eaton FP3-1R5-R High current, low profile inductors

    Eaton FP3-1R5-R is a high current, low profile inductor in a 7.25 x 6.7 mm surface-mount package. It carries 1.5 uH of open-circuit inductance with 5.78 A Irms and a typical DCR of 10 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 3.0 mm tall and rated from -40 °C to +155 °C.

    Electrical Specifications

    Orderable part numberFP3-1R5-R
    Inductance, OCL (0 Adc)1.5 uH
    Irms (40 °C rise, no core loss)5.78 A
    Isat6.2 A
    Isat28 A
    DCR typical @ +20 °C10 mOhm
    DCR maximum @ +20 °C13.1 mOhm
    K-factor (Bp-p = K x L x dI)185
    Package7.25 x 6.7 mm, 3.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +155 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    1.5 uH is the unbiased inductance. The data sheet does not publish a separate full-load figure for this part, so leave margin when you compute ripple at rated current.

    Saturation is quoted as the quoted roll-off at 6.2 A. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Irms of 5.78 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 10 mOhm that is roughly 334 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    The K-factor of 185 turns ripple into flux: a peak-to-peak swing of 1.86 A gives about 51.6 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    What This Family Is For

    This is one of the smaller bodies in the FP range. At 7.25 x 6.7 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 1.5 uH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 6 of 12 when the data sheet is sorted by inductance, DCR sits between the 1 and 106 mOhm the series covers.

    • Application fit: Voltage Regulator Modules (VRMs), Multi-phase regulators, Desktop and server VRMs and EVRDs.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +155 °C, ambient plus self-temperature rise.

    Design Notes

    Size the inductor on peak current first, not average. With 1.5 uH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 10 mOhm the winding is not the loss, the trace can be.

    Mechanical Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP3-1R5-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message