Eaton FP3-2R0-R 5.4 A SMD Power Inductor, 2 uH
Eaton FP3-2R0-R 5.4 A SMD Power Inductor, 2 uH

Eaton FP3-2R0-R 5.4 A SMD Power Inductor, 2 uH

Share
pEaton FP3-2R0-R: 2 uH high current, low profile inductor, 5.4 A Irms, 5.4 A Isat, DCR 11.5 mOhm, 7.25 x 6.7 mm package./p
    • Product Details
    • Download

    FP3-2R0-R at a glance: 2 uH high current, low profile inductor, 5.4 A Irms, 5.4 A Isat, DCR 11.5 mOhm, 7.25 x 6.7 mm body, 3.0 mm tall.

    Eaton FP3-2R0-R High current, low profile inductors

    Eaton FP3-2R0-R is a high current, low profile inductor in a 7.25 x 6.7 mm surface-mount package. It carries 2 uH of open-circuit inductance with 5.4 A Irms and a typical DCR of 11.5 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 3.0 mm tall and rated from -40 °C to +155 °C.

    Specification Table

    Orderable part numberFP3-2R0-R
    Inductance, OCL (0 Adc)2 uH
    Irms (40 °C rise, no core loss)5.4 A
    Isat5.4 A
    Isat26.9 A
    DCR typical @ +20 °C11.5 mOhm
    DCR maximum @ +20 °C15 mOhm
    K-factor (Bp-p = K x L x dI)161
    Package7.25 x 6.7 mm, 3.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +155 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    2 uH is the unbiased inductance. The data sheet does not publish a separate full-load figure for this part, so leave margin when you compute ripple at rated current.

    The first Isat column, 5.4 A, is the peak the part takes at the quoted roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    The 335 mW dissipated at 5.4 A through 11.5 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    The K-factor of 161 turns ripple into flux: a peak-to-peak swing of 1.62 A gives about 52.2 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Positioning in the FP Range

    This is one of the smaller bodies in the FP range. At 7.25 x 6.7 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 2 uH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 7 of 12 when the data sheet is sorted by inductance, DCR sits between the 1 and 106 mOhm the series covers.

    • Application fit: Voltage Regulator Modules (VRMs), Multi-phase regulators, Desktop and server VRMs and EVRDs.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +155 °C, ambient plus self-temperature rise.

    Putting It to Work

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 2 uH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 11.5 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Outline Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP3-2R0-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products