Eaton FP3-3R3-R 3.2 uH 4.3 A Saturation Inductor
Eaton FP3-3R3-R 3.2 uH 4.3 A Saturation Inductor

Eaton FP3-3R3-R 3.2 uH 4.3 A Saturation Inductor

Share
pEaton FP3-3R3-R: 3.2 uH high current, low profile inductor, 3.63 A Irms, 4.3 A Isat, DCR 24.5 mOhm, 7.25 x 6.7 mm package./p
    • Product Details
    • Download

    FP3-3R3-R at a glance: 3.2 uH high current, low profile inductor, 3.63 A Irms, 4.3 A Isat, DCR 24.5 mOhm, 7.25 x 6.7 mm body, 3.0 mm tall.

    Eaton FP3-3R3-R High current, low profile inductors

    Eaton FP3-3R3-R is a high current, low profile inductor in a 7.25 x 6.7 mm surface-mount package. It carries 3.2 uH of open-circuit inductance with 3.63 A Irms and a typical DCR of 24.5 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 3.0 mm tall and rated from -40 °C to +155 °C.

    Ratings at a Glance

    Orderable part numberFP3-3R3-R
    Inductance, OCL (0 Adc)3.2 uH
    Irms (40 °C rise, no core loss)3.63 A
    Isat4.3 A
    Isat25.5 A
    DCR typical @ +20 °C24.5 mOhm
    DCR maximum @ +20 °C30 mOhm
    K-factor (Bp-p = K x L x dI)127
    Package7.25 x 6.7 mm, 3.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +155 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    3.2 uH is the unbiased inductance. The data sheet does not publish a separate full-load figure for this part, so leave margin when you compute ripple at rated current.

    The first Isat column, 4.3 A, is the peak the part takes at the quoted roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Irms of 3.63 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 24.5 mOhm that is roughly 323 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Flux swing follows Bp-p = K x L x dI. With K = 127 and a ripple of 1.29 A the core sees roughly 52.4 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Positioning in the FP Range

    This is one of the smaller bodies in the FP range. At 7.25 x 6.7 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 3.2 uH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 8 of 12 when the data sheet is sorted by inductance, DCR sits between the 1 and 106 mOhm the series covers.

    • Application fit: Voltage Regulator Modules (VRMs), Multi-phase regulators, Desktop and server VRMs and EVRDs.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +155 °C, ambient plus self-temperature rise.

    Putting It to Work

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 3.2 uH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 24.5 mOhm the winding is not the loss, the trace can be.

    Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP3-3R3-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products