
FP3-R10-R at a glance: 100 nH high current, low profile inductor, 19 A Irms, 27 A Isat, DCR 1 mOhm, 7.25 x 6.7 mm body, 3.0 mm tall.
The FP3-R10-R is a 7.25 x 6.7 mm high current, low profile inductor from Eaton, rated 19 A Irms at 100 nH and 1 mOhm typical DCR. It is a surface-mount part 3.0 mm tall, operating from -40 °C to +155 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.
| Orderable part number | FP3-R10-R |
| Inductance, OCL (0 Adc) | 100 nH |
| Irms (40 °C rise, no core loss) | 19 A |
| Isat | 27 A |
| Isat2 | 34.7 A |
| DCR typical @ +20 °C | 1 mOhm |
| DCR maximum @ +20 °C | 1.21 mOhm |
| K-factor (Bp-p = K x L x dI) | 803 |
| Package | 7.25 x 6.7 mm, 3.0 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +155 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
Only the open-circuit value, 100 nH, is tabulated here. With DC in the winding the core will show less, so treat 100 nH as a ceiling rather than an operating value.
Peak current at the quoted roll-off is 27 A. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.
Irms of 19 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 1 mOhm that is roughly 361 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.
The K-factor of 803 turns ripple into flux: a peak-to-peak swing of 8.1 A gives about 65 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.
This is one of the smaller bodies in the FP range. At 7.25 x 6.7 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 100 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.
That makes it the lowest inductance of the 12 parts in this data sheet, and it shares the lowest DCR here at 1 mOhm, Irms of 19 A is the top of the family.
The order of checks that works: compute ripple from 100 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.
On the board, place the part so the switch-node copper is short and wide. At 1 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.
Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

Why does DCR have both a typical and a maximum figure?
The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.
What does the R suffix on the part number mean?
It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd