Eaton FP4-090SK-R - 90 nH Shielded Power Inductor 10.2 x 6.8 mm
Eaton FP4-090SK-R - 90 nH Shielded Power Inductor 10.2 x 6.8 mm

Eaton FP4-090SK-R - 90 nH Shielded Power Inductor 10.2 x 6.8 mm

Share
pEaton FP4-090SK-R: 90 nH high current power inductor, 33 A Irms, 72 A Isat, DCR 0.423-0.517 mOhm, 10.2 x 6.8 mm package./p
    • Product Details
    • Download

    FP4-090SK-R at a glance: 90 nH high current power inductor, 33 A Irms, 72 A Isat, DCR 0.423-0.517 mOhm, 10.2 x 6.8 mm body, 5.0 mm tall.

    Eaton FP4-090SK-R High current power inductors

    FP4-090SK-R is one of Eaton's high current power inductor series, 10.2 x 6.8 mm with a 5.0 mm tall profile. Electrically it offers 90 nH at 33 A Irms and 0.423-0.517 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Electrical Specifications

    Orderable part numberFP4-090SK-R
    Inductance, OCL (0 Adc)90 nH
    Irms (40 °C rise, no core loss)33 A
    Isat (20% roll-off @ +25 °C)72 A
    DCR @ +25 °C0.423-0.517 mOhm
    Volt-microsecond rating1.33 V-us
    Package10.2 x 6.8 mm, 5.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-45 °C to +155 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    90 nH is the unbiased inductance. The data sheet does not publish a separate full-load figure for this part, so leave margin when you compute ripple at rated current.

    The first Isat column, 72 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Irms of 33 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0 mOhm that is roughly 0 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.

    Positioning in the FP Range

    The 10.2 x 6.8 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 90 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it the lowest inductance of the 5 parts in this data sheet, Irms of 33 A is the bottom of the family.

    • Application fit: Servers, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -45 °C to +155 °C, ambient plus self-temperature rise.

    Putting It to Work

    The order of checks that works: compute ripple from 90 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0 mOhm the winding is not the loss, the trace can be.

    Mechanical Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP4-090SK-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products