Eaton FP4-100-R High Current Inductor, 100 nH 0.38 mOhm
Eaton FP4-100-R High Current Inductor, 100 nH 0.38 mOhm

Eaton FP4-100-R High Current Inductor, 100 nH 0.38 mOhm

Share
pEaton FP4-100-R: 100 nH high current power inductor, 40 A Irms, 64 A Isat, DCR 0.38 mOhm, 10.2 x 6.8 mm package./p
    • Product Details
    • Download

    FP4-100-R at a glance: 100 nH high current power inductor, 40 A Irms, 64 A Isat, DCR 0.38 mOhm, 10.2 x 6.8 mm body, 5.0 mm tall.

    Eaton FP4-100-R High current power inductors

    The FP4-100-R is a 10.2 x 6.8 mm high current power inductor from Eaton, rated 40 A Irms at 100 nH and 0.38 mOhm typical DCR. It is a surface-mount part 5.0 mm tall, operating from -45 °C to +155 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Electrical Specifications

    Orderable part numberFP4-100-R
    Inductance, OCL (0 Adc)100 nH
    Irms (40 °C rise, no core loss)40 A
    Isat (20% roll-off @ +25 °C)64 A
    DCR typical @ +20 °C0.38 mOhm
    DCR maximum @ +20 °C0.65 mOhm
    Volt-microsecond rating1.33 V-us
    Package10.2 x 6.8 mm, 5.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-45 °C to +155 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    100 nH is the unbiased inductance. The data sheet does not publish a separate full-load figure for this part, so leave margin when you compute ripple at rated current.

    Peak current at 20% roll-off is 64 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    The 608 mW dissipated at 40 A through 0.38 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.

    Series Positioning

    The 10.2 x 6.8 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 100 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it part 2 of 5 when the data sheet is sorted by inductance, Irms of 40 A is the top of the family.

    • Application fit: Servers, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -45 °C to +155 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    Size the inductor on peak current first, not average. With 100 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    On the board, place the part so the switch-node copper is short and wide. At 0.38 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP4-100-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products