Eaton FP4-150-R 150 nH 42 A Saturation Inductor
Eaton FP4-150-R 150 nH 42 A Saturation Inductor

Eaton FP4-150-R 150 nH 42 A Saturation Inductor

Share
pEaton FP4-150-R: 150 nH high current power inductor, 40 A Irms, 42 A Isat, DCR 0.38 mOhm, 10.2 x 6.8 mm package./p
    • Product Details
    • Download

    FP4-150-R at a glance: 150 nH high current power inductor, 40 A Irms, 42 A Isat, DCR 0.38 mOhm, 10.2 x 6.8 mm body, 5.0 mm tall.

    Eaton FP4-150-R High current power inductors

    The FP4-150-R is a 10.2 x 6.8 mm high current power inductor from Eaton, rated 40 A Irms at 150 nH and 0.38 mOhm typical DCR. It is a surface-mount part 5.0 mm tall, operating from -45 °C to +155 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Key Specifications

    Orderable part numberFP4-150-R
    Inductance, OCL (0 Adc)150 nH
    Irms (40 °C rise, no core loss)40 A
    Isat (20% roll-off @ +25 °C)42 A
    DCR typical @ +20 °C0.38 mOhm
    DCR maximum @ +20 °C0.65 mOhm
    Volt-microsecond rating1.33 V-us
    Package10.2 x 6.8 mm, 5.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-45 °C to +155 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    150 nH is the unbiased inductance. The data sheet does not publish a separate full-load figure for this part, so leave margin when you compute ripple at rated current.

    The first Isat column, 42 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Copper loss at the rated current works out at about 608 mW (40 A squared times 0.38 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.

    Where This Part Sits in the Range

    The 10.2 x 6.8 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 150 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 4 of 5 when the data sheet is sorted by inductance, Irms of 40 A is the top of the family.

    • Application fit: Servers, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -45 °C to +155 °C, ambient plus self-temperature rise.

    Design Notes

    Size the inductor on peak current first, not average. With 150 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.38 mOhm the winding is not the loss, the trace can be.

    Mechanical Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP4-150-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message