Eaton HC1-1R7-R 1.66 uH High-Current Inductor 2 mOhm
Eaton HC1-1R7-R 1.66 uH High-Current Inductor 2 mOhm

Eaton HC1-1R7-R 1.66 uH High-Current Inductor 2 mOhm

Share
Eaton HC1-1R7-R: foil-wound high-current inductor, 1.66 uH ±15%, 22.3 A Irms, Isat 22.2 A, DCR 2 mOhm, 13.0 x 10.0 mm.
    • Product Details
    • Download

    Eaton HC1-1R7-R 1.66 uH High-Current Inductor 2 mOhm

    HC1-1R7-R at a glance: foil-wound high-current inductor, 1.66 uH ±15%, 22.3 A Irms, Isat 22.2 A (30% rolloff @ +20 °C), DCR 2 mOhm, 13.0 x 10.0 mm.

    Specification Table

    ParameterValue
    Orderable part numberHC1-1R7-R
    OCL (open circuit inductance)1.66 uH ±15%
    Irms (DC, 40 °C rise)22.3 A
    Isat (30% rolloff @ +20 °C)22.2 A
    DCR typical @ +20 °C2 mOhm
    Volt-time rating (V-us)7.33
    Package13.0 x 10.0 mm
    Height4.9 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4328

    Dimensions and Pad Layout

    HC1-1R7-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4328: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    This part belongs to the HC foil family, built for high-current, low-voltage converters where efficiency is dominated by the copper. Ferrite keeps core loss low at the switching frequency; the foil winding keeps the copper loss low at the DC component. Both halves of the loss budget are addressed in the same body.

    With 2 mOhm typical, the I-squared-R loss at the full 22.3 A rating is about 0.995 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The saturation rating reads 30% rolloff @ +20 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    At Isat the part holds about 409 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    Positioning in the Range

    The HC foil family covers the low-inductance, very-high-current end of the range: sub-microhenry to a few microhenry, with DC resistance measured in fractions of a milliohm. It is the family to reach for when the rail is a volt or two and the current is tens of amps.

    Within the HC1 family this is value 6 of 11, in a range that runs from 0.218 uH to 10.5 uH.

    The next value up in the same family, HC1-2R3-R, gives 2.29 uH at 22.3 A and DCR 2 mOhm: the extra inductance costs about 5.71 A of rated current.

    • Core material: foil winding, ferrite core, 13.0 x 10.0 mm body at 4.9 mm.
    • Typical applications: distributed power systems dc-dc converters; general-purpose low voltage supplies; computer systems; servers; industrial equipment; data networking and storage systems.
    • The rated current assumes a 40 °C rise from DC alone. AC ripple raises the winding temperature further, and the derating curves in the data sheet are there for exactly that case.

    Design Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 2 mOhm becomes roughly 2.83 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: on a low-voltage rail the DCR drop is a real fraction of the output. Compare the millivolt drop at rated current against the converter tolerance before choosing the smallest inductance in the family.

    • At frequencies above a few hundred kilohertz, check the AC resistance rise before assuming the DC figure holds.
    • Leave clearance for the tape-and-reel orientation if the line places by vision.
    • Confirm the pad layout against the drawing: the terminal geometry sets the solder fillet and therefore the thermal path.

    Frequently Asked Questions

    Is the rated current a continuous rating?
    It is the DC current that produces a 40 °C rise without core loss. Continuous operation at that current is possible only if the board and the airflow remove the heat; the data sheet derating curves cover AC and core loss.

    Can this replace a powdered-core part of the same value?
    Only if the saturation behaviour is acceptable. Ferrite saturates abruptly compared with a powder core, so the transient margin has to be re-checked even when the inductance and DCR look similar.

    Is the part suitable for a SEPIC or buck-boost stage?
    The inductance and current ratings suit it, but check the AC flux swing: in a buck-boost the inductor carries the full input current continuously, so the core loss is higher than in a buck stage of the same output.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products