Eaton HC1-7R8-R 7.85 uH High-Current Inductor 5.7 mOhm
Eaton HC1-7R8-R 7.85 uH High-Current Inductor 5.7 mOhm

Eaton HC1-7R8-R 7.85 uH High-Current Inductor 5.7 mOhm

Share
Eaton HC1-7R8-R: foil-wound high-current inductor, 7.85 uH ±15%, 12.8 A Irms, Isat 6.7 A, DCR 5.7 mOhm, 13.0 x 10.0 mm.
    • Product Details
    • Download

    Eaton HC1-7R8-R 7.85 uH High-Current Inductor 5.7 mOhm

    HC1-7R8-R at a glance: foil-wound high-current inductor, 7.85 uH ±15%, 12.8 A Irms, Isat 6.7 A (30% rolloff @ +20 °C), DCR 5.7 mOhm, 13.0 x 10.0 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHC1-7R8-R
    OCL (open circuit inductance)7.85 uH ±15%
    Irms (DC, 40 °C rise)12.8 A
    Isat (30% rolloff @ +20 °C)6.7 A
    DCR typical @ +20 °C5.7 mOhm
    Volt-time rating (V-us)11
    Package13.0 x 10.0 mm
    Height4.9 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4328

    Outline Drawing

    HC1-7R8-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4328: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Where a power rail delivers tens of amps at a volt or two, the inductor is effectively a short circuit that happens to store energy. The foil construction here minimises the resistance of that short circuit while the ferrite core holds the inductance, which is why the family is used on distributed power and server-class converters.

    The DCR figure of 5.7 mOhm is what sets the efficiency: at 12.8 A the winding drops about 0.073 mV and dissipates 0.932 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    The saturation rating reads 30% rolloff @ +20 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    At Isat the part holds about 176 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    Positioning in the Range

    The HC foil family covers the low-inductance, very-high-current end of the range: sub-microhenry to a few microhenry, with DC resistance measured in fractions of a milliohm. It is the family to reach for when the rail is a volt or two and the current is tens of amps.

    In the HC1 line-up this part is number 10 of 11 by inductance, between 0.218 uH and 10.5 uH.

    The next value up in the same family, HC1-100-R, gives 10.5 uH at 12.8 A and DCR 5.7 mOhm: the extra inductance costs about 0 A of rated current.

    • Core material: foil winding, ferrite core, 13.0 x 10.0 mm body at 4.9 mm.
    • Typical applications: distributed power systems dc-dc converters; general-purpose low voltage supplies; computer systems; servers; industrial equipment; data networking and storage systems.
    • The rated current assumes a 40 °C rise from DC alone. AC ripple raises the winding temperature further, and the derating curves in the data sheet are there for exactly that case.

    Design Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 5.7 mOhm becomes roughly 8.05 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: on a low-voltage rail the DCR drop is a real fraction of the output. Compare the millivolt drop at rated current against the converter tolerance before choosing the smallest inductance in the family.

    • Apply the AC derating curve before assuming the 40 °C rise figure holds.
    • Check the millivolt drop at rated current against the converter tolerance window.
    • Apply the AC derating curve before assuming the 40 °C rise figure holds.

    Frequently Asked Questions

    Why foil instead of round wire?
    At high frequency the current crowds into the surface of the conductor. A flat foil presents a wide surface for the same cross-section, so the AC resistance stays closer to the DC value and the winding runs cooler.

    Can this replace a powdered-core part of the same value?
    Only if the saturation behaviour is acceptable. Ferrite saturates abruptly compared with a powder core, so the transient margin has to be re-checked even when the inductance and DCR look similar.

    Is the part suitable for a SEPIC or buck-boost stage?
    The inductance and current ratings suit it, but check the AC flux swing: in a buck-boost the inductor carries the full input current continuously, so the core loss is higher than in a buck stage of the same output.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products