Eaton HC2-1R0-R Foil-Wound Inductor 1.15 uH, Isat 42.5 A
Eaton HC2-1R0-R Foil-Wound Inductor 1.15 uH, Isat 42.5 A

Eaton HC2-1R0-R Foil-Wound Inductor 1.15 uH, Isat 42.5 A

Share
Eaton HC2-1R0-R: foil-wound high-current inductor, 1.15 uH ±20%, 33 A Irms, Isat 42.5 A, DCR 1.3 mOhm, 19.2 x 19.0 mm.
    • Product Details
    • Download

    Eaton HC2-1R0-R Foil-Wound Inductor 1.15 uH, Isat 42.5 A

    HC2-1R0-R at a glance: foil-wound high-current inductor, 1.15 uH ±20%, 33 A Irms, Isat 42.5 A (20% rolloff @ +25 °C), DCR 1.3 mOhm, 19.2 x 19.0 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHC2-1R0-R
    Ordering code, tape and reelHC2-1R0TR-R
    OCL (open circuit inductance)1.15 uH ±20%
    Irms (DC, 40 °C rise)33 A
    Isat (20% rolloff @ +25 °C)42.5 A
    DCR typical @ +20 °C1.3 mOhm
    Volt-time rating (V-us)10.3
    Package19.2 x 19.0 mm
    Height12.7 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4109

    Mechanical Drawing

    HC2-1R0-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4109: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    This part belongs to the HC foil family, built for high-current, low-voltage converters where efficiency is dominated by the copper. Ferrite keeps core loss low at the switching frequency; the foil winding keeps the copper loss low at the DC component. Both halves of the loss budget are addressed in the same body.

    With 1.3 mOhm typical, the I-squared-R loss at the full 33 A rating is about 1.42 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    Stored energy at Isat is about 1,039 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    Series Positioning

    The HC foil family covers the low-inductance, very-high-current end of the range: sub-microhenry to a few microhenry, with DC resistance measured in fractions of a milliohm. It is the family to reach for when the rail is a volt or two and the current is tens of amps.

    Of the 6 values listed for HC2, this is the 3th, in a family covering 0.52 uH to 6 uH.

    The next value up in the same family, HC2-2R2-R, gives 2.00 uH at 24.3 A and DCR 2.3 mOhm: the extra inductance costs about 28.6 A of rated current.

    • Core material: metal composite, 19.2 x 19.0 mm body at 12.7 mm.
    • Typical applications: distributed power systems dc-dc converters; general-purpose low voltage supplies; computer systems; servers; point of load (pol) converters; industrial equipment.
    • The rated current assumes a 40 °C rise from DC alone. AC ripple raises the winding temperature further, and the derating curves in the data sheet are there for exactly that case.

    Design Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 1.3 mOhm becomes roughly 1.84 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: on a low-voltage rail the DCR drop is a real fraction of the output. Compare the millivolt drop at rated current against the converter tolerance before choosing the smallest inductance in the family.

    • Apply the AC derating curve before assuming the 40 °C rise figure holds.
    • Confirm the pad layout against the drawing: the terminal geometry sets the solder fillet and therefore the thermal path.
    • Apply the AC derating curve before assuming the 40 °C rise figure holds.

    Frequently Asked Questions

    What does the DCR tolerance mean for paralleling?
    Parts are not matched for DCR, so two in parallel will not share current exactly. The mismatch is set by the DCR tolerance, and because the DCR is only fractions of a milliohm, a small absolute difference is a large percentage one.

    Is the rated current a continuous rating?
    It is the DC current that produces a 40 °C rise without core loss. Continuous operation at that current is possible only if the board and the airflow remove the heat; the data sheet derating curves cover AC and core loss.

    What does the volt-microsecond column describe?
    It is the applied volt-time product that produces a core loss equal to 10 % of the total loss at a 40 °C rise. It is a way to compare core capability between parts at a given frequency.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products