Eaton HC2-4R7-R 4.55 uH Foil Power Inductor, 17 A
Eaton HC2-4R7-R 4.55 uH Foil Power Inductor, 17 A

Eaton HC2-4R7-R 4.55 uH Foil Power Inductor, 17 A

Share
Eaton HC2-4R7-R: foil-wound high-current inductor, 4.55 uH ±20%, 17 A Irms, Isat 21.2 A, DCR 4.6 mOhm, 19.2 x 19.0 mm.
    • Product Details
    • Download

    Eaton HC2-4R7-R 4.55 uH Foil Power Inductor, 17 A

    HC2-4R7-R at a glance: foil-wound high-current inductor, 4.55 uH ±20%, 17 A Irms, Isat 21.2 A (20% rolloff @ +25 °C), DCR 4.6 mOhm, 19.2 x 19.0 mm.

    Specification Table

    ParameterValue
    Orderable part numberHC2-4R7-R
    Ordering code, tape and reelHC2-4R7TR-R
    OCL (open circuit inductance)4.55 uH ±20%
    Irms (DC, 40 °C rise)17 A
    Isat (20% rolloff @ +25 °C)21.2 A
    DCR typical @ +20 °C4.6 mOhm
    Volt-time rating (V-us)20.6
    Package19.2 x 19.0 mm
    Height12.7 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4109

    Mechanical Drawing

    HC2-4R7-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4109: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    A foil winding on a ferrite core is the classic answer to a hard combination: several tens of amps, a supply below 5 V, and a switching frequency high enough that skin depth has already eaten into round wire. The flat conductor keeps the window utilisation high, so DCR stays in the fractions of a milliohm.

    With 4.6 mOhm typical, the I-squared-R loss at the full 17 A rating is about 1.33 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    Stored energy at Isat is about 1,027 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    Positioning in the Range

    The HC foil family covers the low-inductance, very-high-current end of the range: sub-microhenry to a few microhenry, with DC resistance measured in fractions of a milliohm. It is the family to reach for when the rail is a volt or two and the current is tens of amps.

    In the HC2 line-up this part is number 5 of 6 by inductance, between 0.52 uH and 6 uH.

    One step down the table, HC2-2R2-R, sits at 2.00 uH with 24.3 A and 2.3 mOhm – the lower inductance buys about 7.3 A of extra current in the same body.

    • Core material: metal composite, 19.2 x 19.0 mm body at 12.7 mm.
    • Typical applications: distributed power systems dc-dc converters; general-purpose low voltage supplies; computer systems; servers; point of load (pol) converters; industrial equipment.
    • The rated current assumes a 40 °C rise from DC alone. AC ripple raises the winding temperature further, and the derating curves in the data sheet are there for exactly that case.

    Design Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 4.6 mOhm becomes roughly 6.5 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: on a low-voltage rail the DCR drop is a real fraction of the output. Compare the millivolt drop at rated current against the converter tolerance before choosing the smallest inductance in the family.

    • Keep the peak current inside the saturation boundary with margin for inductance tolerance.
    • At frequencies above a few hundred kilohertz, check the AC resistance rise before assuming the DC figure holds.
    • Leave clearance for the tape-and-reel orientation if the line places by vision.

    Frequently Asked Questions

    Is the rated current a continuous rating?
    It is the DC current that produces a 40 °C rise without core loss. Continuous operation at that current is possible only if the board and the airflow remove the heat; the data sheet derating curves cover AC and core loss.

    Is the part suitable for a SEPIC or buck-boost stage?
    The inductance and current ratings suit it, but check the AC flux swing: in a buck-boost the inductor carries the full input current continuously, so the core loss is higher than in a buck stage of the same output.

    What does the DCR tolerance mean for paralleling?
    Parts are not matched for DCR, so two in parallel will not share current exactly. The mismatch is set by the DCR tolerance, and because the DCR is only fractions of a milliohm, a small absolute difference is a large percentage one.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products