Eaton HC2-6R0-R 6.00 uH Ferrite Foil Inductor
Eaton HC2-6R0-R 6.00 uH Ferrite Foil Inductor

Eaton HC2-6R0-R 6.00 uH Ferrite Foil Inductor

Share
Eaton HC2-6R0-R: foil-wound high-current inductor, 6.00 uH ±20%, 17 A Irms, Isat 16.5 A, DCR 4.6 mOhm, 19.2 x 19.0 mm.
    • Product Details
    • Download

    Eaton HC2-6R0-R 6.00 uH Ferrite Foil Inductor

    HC2-6R0-R at a glance: foil-wound high-current inductor, 6.00 uH ±20%, 17 A Irms, Isat 16.5 A (20% rolloff @ +25 °C), DCR 4.6 mOhm, 19.2 x 19.0 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHC2-6R0-R
    Ordering code, tape and reelHC2-6R0TR-R
    OCL (open circuit inductance)6.00 uH ±20%
    Irms (DC, 40 °C rise)17 A
    Isat (20% rolloff @ +25 °C)16.5 A
    DCR typical @ +20 °C4.6 mOhm
    Volt-time rating (V-us)20.6
    Package19.2 x 19.0 mm
    Height12.7 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4109

    Mechanical Drawing

    HC2-6R0-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4109: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    The winding in this part is copper foil rather than magnet wire. Foil gives the conductor a wide, flat section, so the high-frequency current crowds into a much larger effective area and the AC resistance stays close to the DC value. On a low-voltage, high-current rail that is the difference between an inductor that runs cool at 300 kHz and one that cooks.

    At the rated 17 A the winding dissipates about 1.33 W in copper alone, using the typical DCR of 4.6 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    The core stores roughly 817 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    Where This Series Fits

    The HC foil family covers the low-inductance, very-high-current end of the range: sub-microhenry to a few microhenry, with DC resistance measured in fractions of a milliohm. It is the family to reach for when the rail is a volt or two and the current is tens of amps.

    Of the 6 values listed for HC2, this is the 6th, in a family covering 0.52 uH to 6 uH.

    The next value up in the same family, HC2-4R7-R, gives 4.55 uH at 17 A and DCR 4.6 mOhm: the extra inductance costs about 0 A of rated current.

    • Core material: metal composite, 19.2 x 19.0 mm body at 12.7 mm.
    • Typical applications: distributed power systems dc-dc converters; general-purpose low voltage supplies; computer systems; servers; point of load (pol) converters; industrial equipment.
    • The rated current assumes a 40 °C rise from DC alone. AC ripple raises the winding temperature further, and the derating curves in the data sheet are there for exactly that case.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 4.6 mOhm becomes roughly 6.5 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: on a low-voltage rail the DCR drop is a real fraction of the output. Compare the millivolt drop at rated current against the converter tolerance before choosing the smallest inductance in the family.

    • At frequencies above a few hundred kilohertz, check the AC resistance rise before assuming the DC figure holds.
    • Leave clearance for the tape-and-reel orientation if the line places by vision.
    • Apply the AC derating curve before assuming the 40 °C rise figure holds.

    Frequently Asked Questions

    Is the rated current a continuous rating?
    It is the DC current that produces a 40 °C rise without core loss. Continuous operation at that current is possible only if the board and the airflow remove the heat; the data sheet derating curves cover AC and core loss.

    Why foil instead of round wire?
    At high frequency the current crowds into the surface of the conductor. A flat foil presents a wide surface for the same cross-section, so the AC resistance stays closer to the DC value and the winding runs cooler.

    Why foil instead of round wire?
    At high frequency the current crowds into the surface of the conductor. A flat foil presents a wide surface for the same cross-section, so the AC resistance stays closer to the DC value and the winding runs cooler.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products