Eaton HC2-R47-R 0.52 uH Foil Power Inductor, 52.9 A
Eaton HC2-R47-R 0.52 uH Foil Power Inductor, 52.9 A

Eaton HC2-R47-R 0.52 uH Foil Power Inductor, 52.9 A

Share
Eaton HC2-R47-R: foil-wound high-current inductor, 0.52 uH ±20%, 52.9 A Irms, Isat 63.8 A, DCR 0.6 mOhm, 19.2 x 19.0 mm.
    • Product Details
    • Download

    Eaton HC2-R47-R .52 uH Foil Power Inductor, 52.9 A

    HC2-R47-R at a glance: foil-wound high-current inductor, .52 uH ±20%, 52.9 A Irms, Isat 63.8 A (20% rolloff @ +25 °C), DCR 0.6 mOhm, 19.2 x 19.0 mm.

    Specification Table

    ParameterValue
    Orderable part numberHC2-R47-R
    Ordering code, tape and reelHC2-R47TR-R
    OCL (open circuit inductance).52 uH ±20%
    Irms (DC, 40 °C rise)52.9 A
    Isat (20% rolloff @ +25 °C)63.8 A
    DCR typical @ +20 °C0.6 mOhm
    Volt-time rating (V-us)6.87
    Package19.2 x 19.0 mm
    Height12.7 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4109

    Dimensions and Pad Layout

    HC2-R47-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4109: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Where a power rail delivers tens of amps at a volt or two, the inductor is effectively a short circuit that happens to store energy. The foil construction here minimises the resistance of that short circuit while the ferrite core holds the inductance, which is why the family is used on distributed power and server-class converters.

    With 0.6 mOhm typical, the I-squared-R loss at the full 52.9 A rating is about 1.68 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    At Isat the part holds about 1,057 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    Positioning in the Range

    The HC foil family covers the low-inductance, very-high-current end of the range: sub-microhenry to a few microhenry, with DC resistance measured in fractions of a milliohm. It is the family to reach for when the rail is a volt or two and the current is tens of amps.

    Of the 6 values listed for HC2, this is the 1th, in a family covering 0.52 uH to 6 uH.

    Compared with its neighbours in the table, HC2-R68-R trades 0 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: metal composite, 19.2 x 19.0 mm body at 12.7 mm.
    • Typical applications: distributed power systems dc-dc converters; general-purpose low voltage supplies; computer systems; servers; point of load (pol) converters; industrial equipment.
    • The rated current assumes a 40 °C rise from DC alone. AC ripple raises the winding temperature further, and the derating curves in the data sheet are there for exactly that case.

    Design Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 0.6 mOhm becomes roughly 0.848 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: on a low-voltage rail the DCR drop is a real fraction of the output. Compare the millivolt drop at rated current against the converter tolerance before choosing the smallest inductance in the family.

    • Keep the peak current inside the saturation boundary with margin for inductance tolerance.
    • Leave clearance for the tape-and-reel orientation if the line places by vision.
    • Confirm the pad layout against the drawing: the terminal geometry sets the solder fillet and therefore the thermal path.

    Frequently Asked Questions

    Is the rated current a continuous rating?
    It is the DC current that produces a 40 °C rise without core loss. Continuous operation at that current is possible only if the board and the airflow remove the heat; the data sheet derating curves cover AC and core loss.

    Is the rated current a continuous rating?
    It is the DC current that produces a 40 °C rise without core loss. Continuous operation at that current is possible only if the board and the airflow remove the heat; the data sheet derating curves cover AC and core loss.

    Can this replace a powdered-core part of the same value?
    Only if the saturation behaviour is acceptable. Ferrite saturates abruptly compared with a powder core, so the transient margin has to be re-checked even when the inductance and DCR look similar.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products