Eaton HC2LP-1R0-R 1.15 uH Foil Power Inductor, 33 A
Eaton HC2LP-1R0-R 1.15 uH Foil Power Inductor, 33 A

Eaton HC2LP-1R0-R 1.15 uH Foil Power Inductor, 33 A

Share
Eaton HC2LP-1R0-R: foil-wound high-current inductor, 1.15 uH ±20%, 33 A Irms, Isat 42.5 A, DCR 1.3 mOhm, 19.2 x 19.2 mm.
    • Product Details
    • Download

    Eaton HC2LP-1R0-R 1.15 uH Foil Power Inductor, 33 A

    HC2LP-1R0-R at a glance: foil-wound high-current inductor, 1.15 uH ±20%, 33 A Irms, Isat 42.5 A (20% rolloff @ +25 °C), DCR 1.3 mOhm, 19.2 x 19.2 mm.

    Specification Table

    ParameterValue
    Orderable part numberHC2LP-1R0-R
    OCL (open circuit inductance)1.15 uH ±20%
    Irms (DC, 40 °C rise)33 A
    Isat (20% rolloff @ +25 °C)42.5 A
    DCR typical @ +20 °C1.3 mOhm
    Volt-time rating (V-us)10.3
    Package19.2 x 19.2 mm
    Height11.18 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4114

    Mechanical Drawing

    HC2LP-1R0-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4114: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    The winding in this part is copper foil rather than magnet wire. Foil gives the conductor a wide, flat section, so the high-frequency current crowds into a much larger effective area and the AC resistance stays close to the DC value. On a low-voltage, high-current rail that is the difference between an inductor that runs cool at 300 kHz and one that cooks.

    The DCR figure of 1.3 mOhm is what sets the efficiency: at 33 A the winding drops about 0.043 mV and dissipates 1.42 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    Stored energy at Isat is about 1,039 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    Positioning in the Range

    The HC foil family covers the low-inductance, very-high-current end of the range: sub-microhenry to a few microhenry, with DC resistance measured in fractions of a milliohm. It is the family to reach for when the rail is a volt or two and the current is tens of amps.

    The HC2LP family spans 0.52 uH to 6 uH; this row sits at position 3 of 6.

    Compared with its neighbours in the table, HC2LP-2R2-R trades 28.6 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: ferrite core, 19.2 x 19.2 mm body at 11.18 mm.
    • Typical applications: distributed power systems dc-dc converters; general-purpose low voltage supplies; computer systems; servers; point of load (pol) converters; industrial equipment.
    • The rated current assumes a 40 °C rise from DC alone. AC ripple raises the winding temperature further, and the derating curves in the data sheet are there for exactly that case.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 1.3 mOhm becomes roughly 1.84 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: on a low-voltage rail the DCR drop is a real fraction of the output. Compare the millivolt drop at rated current against the converter tolerance before choosing the smallest inductance in the family.

    • Leave clearance for the tape-and-reel orientation if the line places by vision.
    • At frequencies above a few hundred kilohertz, check the AC resistance rise before assuming the DC figure holds.
    • Leave clearance for the tape-and-reel orientation if the line places by vision.

    Frequently Asked Questions

    Can this replace a powdered-core part of the same value?
    Only if the saturation behaviour is acceptable. Ferrite saturates abruptly compared with a powder core, so the transient margin has to be re-checked even when the inductance and DCR look similar.

    Is the part suitable for a SEPIC or buck-boost stage?
    The inductance and current ratings suit it, but check the AC flux swing: in a buck-boost the inductor carries the full input current continuously, so the core loss is higher than in a buck stage of the same output.

    What does the volt-microsecond column describe?
    It is the applied volt-time product that produces a core loss equal to 10 % of the total loss at a 40 °C rise. It is a way to compare core capability between parts at a given frequency.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products