Eaton HC2LP-2R2-R 2.00 uH Ferrite Foil Inductor
Eaton HC2LP-2R2-R 2.00 uH Ferrite Foil Inductor

Eaton HC2LP-2R2-R 2.00 uH Ferrite Foil Inductor

Share
Eaton HC2LP-2R2-R: foil-wound high-current inductor, 2.00 uH ±20%, 24.3 A Irms, Isat 31.9 A, DCR 2.3 mOhm, 19.2 x 19.2 mm.
    • Product Details
    • Download

    Eaton HC2LP-2R2-R 2.00 uH Ferrite Foil Inductor

    HC2LP-2R2-R at a glance: foil-wound high-current inductor, 2.00 uH ±20%, 24.3 A Irms, Isat 31.9 A (20% rolloff @ +25 °C), DCR 2.3 mOhm, 19.2 x 19.2 mm.

    Specification Table

    ParameterValue
    Orderable part numberHC2LP-2R2-R
    OCL (open circuit inductance)2.00 uH ±20%
    Irms (DC, 40 °C rise)24.3 A
    Isat (20% rolloff @ +25 °C)31.9 A
    DCR typical @ +20 °C2.3 mOhm
    Volt-time rating (V-us)13.8
    Package19.2 x 19.2 mm
    Height11.18 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4114

    Outline Drawing

    HC2LP-2R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4114: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    The winding in this part is copper foil rather than magnet wire. Foil gives the conductor a wide, flat section, so the high-frequency current crowds into a much larger effective area and the AC resistance stays close to the DC value. On a low-voltage, high-current rail that is the difference between an inductor that runs cool at 300 kHz and one that cooks.

    The DCR figure of 2.3 mOhm is what sets the efficiency: at 24.3 A the winding drops about 0.056 mV and dissipates 1.36 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    At Isat the part holds about 1,018 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    Series Positioning

    The HC foil family covers the low-inductance, very-high-current end of the range: sub-microhenry to a few microhenry, with DC resistance measured in fractions of a milliohm. It is the family to reach for when the rail is a volt or two and the current is tens of amps.

    The HC2LP family spans 0.52 uH to 6 uH; this row sits at position 4 of 6.

    The next value up in the same family, HC2LP-4R7-R, gives 4.55 uH at 17 A and DCR 4.6 mOhm: the extra inductance costs about 16 A of rated current.

    • Core material: ferrite core, 19.2 x 19.2 mm body at 11.18 mm.
    • Typical applications: distributed power systems dc-dc converters; general-purpose low voltage supplies; computer systems; servers; point of load (pol) converters; industrial equipment.
    • The rated current assumes a 40 °C rise from DC alone. AC ripple raises the winding temperature further, and the derating curves in the data sheet are there for exactly that case.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 2.3 mOhm becomes roughly 3.25 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: on a low-voltage rail the DCR drop is a real fraction of the output. Compare the millivolt drop at rated current against the converter tolerance before choosing the smallest inductance in the family.

    • Keep the peak current inside the saturation boundary with margin for inductance tolerance.
    • Check the millivolt drop at rated current against the converter tolerance window.
    • Apply the AC derating curve before assuming the 40 °C rise figure holds.

    Frequently Asked Questions

    Can this replace a powdered-core part of the same value?
    Only if the saturation behaviour is acceptable. Ferrite saturates abruptly compared with a powder core, so the transient margin has to be re-checked even when the inductance and DCR look similar.

    Is the part suitable for a SEPIC or buck-boost stage?
    The inductance and current ratings suit it, but check the AC flux swing: in a buck-boost the inductor carries the full input current continuously, so the core loss is higher than in a buck stage of the same output.

    Is the rated current a continuous rating?
    It is the DC current that produces a 40 °C rise without core loss. Continuous operation at that current is possible only if the board and the airflow remove the heat; the data sheet derating curves cover AC and core loss.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products