Eaton HC3-5R6-R 5.68 uH Foil Power Inductor, 33.8 A
Eaton HC3-5R6-R 5.68 uH Foil Power Inductor, 33.8 A

Eaton HC3-5R6-R 5.68 uH Foil Power Inductor, 33.8 A

Share
Eaton HC3-5R6-R: foil-wound high-current inductor, 5.68 uH ±20%, 33.8 A Irms, Isat 34.5 A, DCR 2.17 mOhm, 30.0 x 25.3 mm.
    • Product Details
    • Download

    Eaton HC3-5R6-R 5.68 uH Foil Power Inductor, 33.8 A

    HC3-5R6-R at a glance: foil-wound high-current inductor, 5.68 uH ±20%, 33.8 A Irms, Isat 34.5 A (20% rolloff @ +25 °C), DCR 2.17 mOhm, 30.0 x 25.3 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHC3-5R6-R
    OCL (open circuit inductance)5.68 uH ±20%
    Irms (DC, 40 °C rise)33.8 A
    Isat (20% rolloff @ +25 °C)34.5 A
    DCR typical @ +20 °C2.17 mOhm
    Volt-time rating (V-us)43.3
    Package30.0 x 25.3 mm
    Height18.0 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4122

    Mechanical Drawing

    HC3-5R6-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4122: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    The winding in this part is copper foil rather than magnet wire. Foil gives the conductor a wide, flat section, so the high-frequency current crowds into a much larger effective area and the AC resistance stays close to the DC value. On a low-voltage, high-current rail that is the difference between an inductor that runs cool at 300 kHz and one that cooks.

    With 2.17 mOhm typical, the I-squared-R loss at the full 33.8 A rating is about 2.48 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    Stored energy at Isat is about 3,380 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    Positioning in the Range

    The HC foil family covers the low-inductance, very-high-current end of the range: sub-microhenry to a few microhenry, with DC resistance measured in fractions of a milliohm. It is the family to reach for when the rail is a volt or two and the current is tens of amps.

    Within the HC3 family this is value 6 of 7, in a range that runs from 0.5 uH to 6.52 uH.

    Compared with its neighbours in the table, HC3-6R0-R trades 0 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: ferrite core, 30.0 x 25.3 mm body at 18.0 mm.
    • Typical applications: distributed power systems dc-dc converters; general-purpose low voltage supplies; computer systems; servers; point of load (pol) converters; industrial equipment.
    • The rated current assumes a 40 °C rise from DC alone. AC ripple raises the winding temperature further, and the derating curves in the data sheet are there for exactly that case.

    Design Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 2.17 mOhm becomes roughly 3.07 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: on a low-voltage rail the DCR drop is a real fraction of the output. Compare the millivolt drop at rated current against the converter tolerance before choosing the smallest inductance in the family.

    • Leave clearance for the tape-and-reel orientation if the line places by vision.
    • Apply the AC derating curve before assuming the 40 °C rise figure holds.
    • Check the millivolt drop at rated current against the converter tolerance window.

    Frequently Asked Questions

    Why foil instead of round wire?
    At high frequency the current crowds into the surface of the conductor. A flat foil presents a wide surface for the same cross-section, so the AC resistance stays closer to the DC value and the winding runs cooler.

    Is the rated current a continuous rating?
    It is the DC current that produces a 40 °C rise without core loss. Continuous operation at that current is possible only if the board and the airflow remove the heat; the data sheet derating curves cover AC and core loss.

    Why foil instead of round wire?
    At high frequency the current crowds into the surface of the conductor. A flat foil presents a wide surface for the same cross-section, so the AC resistance stays closer to the DC value and the winding runs cooler.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products