Eaton HC7-3R9-R Powder Iron Inductor 3.61 uH, Isat 10.6 A
Eaton HC7-3R9-R Powder Iron Inductor 3.61 uH, Isat 10.6 A

Eaton HC7-3R9-R Powder Iron Inductor 3.61 uH, Isat 10.6 A

Share
Eaton HC7-3R9-R: powder iron high-current inductor, 3.61 uH ±20%, 10.4 A Irms, Isat 10.6 A, DCR 7.9 mOhm, 13.8 mm long.
    • Product Details
    • Download

    Eaton HC7-3R9-R Powder Iron Inductor 3.61 uH, Isat 10.6 A

    HC7-3R9-R at a glance: powder iron high-current inductor, 3.61 uH ±20%, 10.4 A Irms, Isat 10.6 A (15% rolloff), DCR 7.9 mOhm, 13.8 mm long.

    Specification Table

    ParameterValue
    Orderable part numberHC7-3R9-R
    OCL (open circuit inductance)3.61 uH ±20%
    Irms (DC, 40 °C rise)10.4 A
    Isat (15% rolloff)10.6 A
    Isat2 (30% rolloff)20 A
    DCR typical @ +20 °C7.9 mOhm
    Volt-time rating (V-us)10
    Package13.8 mm long
    Height5.5 mm
    MountingSurface mount
    Operating temperature-40 °C to +155 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4116

    Mechanical Drawing

    HC7-3R9-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4116: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    A powder core with a non-organic binder is a deliberately conservative choice: it trades a little permeability for predictable behaviour at high current and high temperature. The result is an inductor that stays linear enough for a current-mode loop to be designed around it.

    The DCR figure of 7.9 mOhm is what sets the efficiency: at 10.4 A the winding drops about 0.082 mV and dissipates 0.854 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Isat is specified as 15% rolloff, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    Stored energy at Isat is about 203 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    The second saturation column, 20 A at 30% rolloff, is the same core taken further into rolloff. The ratio between the two columns is a direct measure of how soft the curve is: a part with a wide gap between them loses inductance slowly and tolerates a larger transient peak.

    Series Positioning

    The HC powder family sits at the higher-inductance end of the high-current range: from a fraction of a microhenry up to tens of microhenry, on surface-mount bodies with powder iron cores. Every row carries two saturation columns so the rolloff criterion can be chosen explicitly.

    Of the 7 values listed for HC7, this is the 6th, in a family covering 0.22 uH to 4.81 uH.

    The next value up in the same family, HC7-4R7-R, gives 4.81 uH at 9.8 A and DCR 9 mOhm: the extra inductance costs about 3.2 A of rated current.

    • Core material: powder iron core, 13.8 mm long body at 5.5 mm.
    • Typical applications: multi-phase regulators; voltage regulator modules (vrms); distributed power systems dc-dc converters; desktop and server vrms and evrds; point-of-load (pol) modules; field programmable gate array (fpga) dc-dc converters.
    • The two saturation columns are different criteria, not two measurements of the same thing. Pick the rolloff you can tolerate in the application and stay with that column.

    Design Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 7.9 mOhm becomes roughly 12.1 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: use the 30% rolloff column only if the loop can tolerate the inductance droop; the tighter column keeps more inductance at the cost of a lower usable peak current.

    • Decide which rolloff column the loop can tolerate, then stay with that column.
    • Decide which rolloff column the loop can tolerate, then stay with that column.
    • Check that the inductance at the working DC bias still meets the ripple target.

    Frequently Asked Questions

    Why is the DCR higher than a ferrite part of the same size?
    Iron powder has lower permeability, so more turns are needed for the same inductance, and more turns mean more copper. The compensation is the much higher saturation flux density.

    Which saturation column should I design to?
    The one that matches the inductance droop your loop can tolerate. The 30 % column gives a higher usable peak current; the tighter column keeps more inductance at the cost of headroom.

    Does the inductance drift with age?
    The binder is non-organic and the core is not gapped with adhesive, so thermal aging of the magnetic path is not a mechanism here. The value is stable across thermal cycles.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products