Eaton HC8LP-330-R 32.1 uH High-Current Inductor 224 mOhm
Eaton HC8LP-330-R 32.1 uH High-Current Inductor 224 mOhm

Eaton HC8LP-330-R 32.1 uH High-Current Inductor 224 mOhm

Share
Eaton HC8LP-330-R: powder iron high-current inductor, 32.1 uH ±20%, 2.3 A Irms, Isat 2.1 A, DCR 224 mOhm, 10.9 x 10.4 mm.
    • Product Details
    • Download

    Eaton HC8LP-330-R 32.1 uH High-Current Inductor 224 mOhm

    HC8LP-330-R at a glance: powder iron high-current inductor, 32.1 uH ±20%, 2.3 A Irms, Isat 2.1 A (15% rolloff), DCR 224 mOhm, 10.9 x 10.4 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHC8LP-330-R
    OCL (open circuit inductance)32.1 uH ±20%
    Irms (DC, 40 °C rise)2.3 A
    Isat (15% rolloff)2.1 A
    Isat2 (30% rolloff)3.8 A
    DCR typical @ +20 °C224 mOhm
    Volt-time rating (V-us)16.8
    Package10.9 x 10.4 mm
    Height3.5 mm
    MountingSurface mount
    Operating temperature-40 °C to +155 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4126

    Mechanical Drawing

    HC8LP-330-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4126: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    The core is iron powder held in a high-temperature non-organic binder. That construction does not saturate abruptly: as current rises the permeability falls progressively, so the inductance droops instead of collapsing. For a switching regulator working near its current limit during a transient, that behaviour keeps the control loop in a known place.

    The DCR figure of 224 mOhm is what sets the efficiency: at 2.3 A the winding drops about 0.515 mV and dissipates 1.19 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    The Isat column is 15% rolloff. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    The core stores roughly 70.8 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The second saturation column, 3.8 A at 30% rolloff, is the same core taken further into rolloff. The ratio between the two columns is a direct measure of how soft the curve is: a part with a wide gap between them loses inductance slowly and tolerates a larger transient peak.

    Positioning in the Range

    The HC powder family sits at the higher-inductance end of the high-current range: from a fraction of a microhenry up to tens of microhenry, on surface-mount bodies with powder iron cores. Every row carries two saturation columns so the rolloff criterion can be chosen explicitly.

    Of the 16 values listed for HC8LP, this is the 15th, in a family covering 0.17 uH to 47.9 uH.

    Compared with its neighbours in the table, HC8LP-470-R trades 1 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: powder iron core, 10.9 x 10.4 mm body at 3.5 mm.
    • Typical applications: multi-phase regulators; voltage regulator modules (vrms); distributed power systems dc-dc converters; notebook and laptop regulators; desktop and server vrms and evrds; point-of-load (pol) modules.
    • The two saturation columns are different criteria, not two measurements of the same thing. Pick the rolloff you can tolerate in the application and stay with that column.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 224 mOhm becomes roughly 343 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: use the 30% rolloff column only if the loop can tolerate the inductance droop; the tighter column keeps more inductance at the cost of a lower usable peak current.

    • Compare the two saturation columns before fixing the current limit in the controller.
    • Decide which rolloff column the loop can tolerate, then stay with that column.
    • Confirm the part marking is visible after placement for traceability.

    Frequently Asked Questions

    Does the inductance drift with age?
    The binder is non-organic and the core is not gapped with adhesive, so thermal aging of the magnetic path is not a mechanism here. The value is stable across thermal cycles.

    Why is the DCR higher than a ferrite part of the same size?
    Iron powder has lower permeability, so more turns are needed for the same inductance, and more turns mean more copper. The compensation is the much higher saturation flux density.

    What is soft saturation?
    The inductance falls gradually as current rises instead of collapsing at a threshold. A powder core with a distributed gap behaves this way, which keeps the converter stable through a load transient.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products