Eaton HC9-R47-R Powder Iron Inductor 0.544 uH, Isat 40 A
Eaton HC9-R47-R Powder Iron Inductor 0.544 uH, Isat 40 A

Eaton HC9-R47-R Powder Iron Inductor 0.544 uH, Isat 40 A

Share
Eaton HC9-R47-R: powder iron high-current inductor, 0.544 uH ±15%, 33.7 A Irms, Isat 40 A, DCR 0.88 mOhm, 13.1 x 14.1 mm.
    • Product Details
    • Download

    Eaton HC9-R47-R Powder Iron Inductor 0.544 uH, Isat 40 A

    HC9-R47-R at a glance: powder iron high-current inductor, 0.544 uH ±15%, 33.7 A Irms, Isat 40 A (20% rolloff), DCR 0.88 mOhm, 13.1 x 14.1 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHC9-R47-R
    OCL (open circuit inductance)0.544 uH ±15%
    Irms (DC, 40 °C rise)33.7 A
    Isat (20% rolloff)40 A
    Isat2 (30% rolloff)57 A
    DCR typical @ +20 °C0.88 mOhm
    Volt-time rating (V-us)4.78
    Package13.1 x 14.1 mm
    Height7.5 mm
    MountingSurface mount
    Operating temperature-40 °C to +155 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data DS4312

    Mechanical Drawing

    HC9-R47-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data DS4312: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    Powder iron is the material choice that gives this family its soft saturation curve and its stable inductance over temperature. There is no thermal aging of the binder, so the inductance you measure on day one is the inductance you have after a thousand thermal cycles.

    With 0.88 mOhm typical, the I-squared-R loss at the full 33.7 A rating is about 0.999 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The Isat column is 20% rolloff. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    The core stores roughly 435 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The second saturation column, 57 A at 30% rolloff, is the same core taken further into rolloff. The ratio between the two columns is a direct measure of how soft the curve is: a part with a wide gap between them loses inductance slowly and tolerates a larger transient peak.

    Positioning in the Range

    The HC powder family sits at the higher-inductance end of the high-current range: from a fraction of a microhenry up to tens of microhenry, on surface-mount bodies with powder iron cores. Every row carries two saturation columns so the rolloff criterion can be chosen explicitly.

    Of the 12 values listed for HC9, this is the 2th, in a family covering 0.218 uH to 49.2 uH.

    Compared with its neighbours in the table, HC9-1R0-R trades 23 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: powder iron core, 13.1 x 14.1 mm body at 7.5 mm.
    • Typical applications: multi-phase regulators; voltage regulator modules (vrms); distributed power systems dc-dc converters; desktop and server vrms and evrds; point-of-load (pol) modules; field programmable gate array (fpga) dc-dc converters.
    • The two saturation columns are different criteria, not two measurements of the same thing. Pick the rolloff you can tolerate in the application and stay with that column.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 0.88 mOhm becomes roughly 1.35 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: use the 30% rolloff column only if the loop can tolerate the inductance droop; the tighter column keeps more inductance at the cost of a lower usable peak current.

    • Confirm the part marking is visible after placement for traceability.
    • Check that the inductance at the working DC bias still meets the ripple target.
    • Confirm the part marking is visible after placement for traceability.

    Frequently Asked Questions

    How do I estimate the inductance at my operating current?
    Read it off the inductance-versus-DC-bias curve in the data sheet at the actual bias. The curve, not the OCL value, is what sets the ripple at load.

    Is the part shielded?
    The winding is enclosed by the powder core, so the external field is small. It is not a closed ferrite shield, but the fringing field is low enough for dense board layouts.

    How do I estimate the inductance at my operating current?
    Read it off the inductance-versus-DC-bias curve in the data sheet at the actual bias. The curve, not the OCL value, is what sets the ripple at load.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products