Eaton HCF1007-R56-R 0.56 uH Low-Loss Power Inductor
Eaton HCF1007-R56-R 0.56 uH Low-Loss Power Inductor

Eaton HCF1007-R56-R 0.56 uH Low-Loss Power Inductor

Share
Eaton HCF1007-R56-R: ferrite high-current power inductor, 0.56 uH ±20%, 26 A Irms, Isat 36 A, DCR 1.3 mOhm, 10.3 x 8.1 mm.
    • Product Details
    • Download

    Eaton HCF1007-R56-R 0.56 uH Low-Loss Power Inductor

    HCF1007-R56-R at a glance: ferrite high-current power inductor, 0.56 uH ±20%, 26 A Irms, Isat 36 A (20% rolloff @ +25 °C), DCR 1.3 mOhm, 10.3 x 8.1 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCF1007-R56-R
    OCL (open circuit inductance)0.56 uH ±20%
    FLL minimum, at Isat0.4 uH
    Irms (DC, 40 °C rise)26 A
    Isat (20% rolloff @ +25 °C)36 A
    Isat2 (20% rolloff @ +125 °C)28 A
    DCR typical @ +20 °C1.3 mOhm
    K-factor (Bp-p = K x L x dI)187, Bp-p in Gauss
    Package10.3 x 8.1 mm
    Height6.65 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4361

    Mechanical Drawing

    HCF1007-R56-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4361: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    The core is ferrite, and the family is characterised at two temperatures: the saturation current is quoted at +25 °C and again at +125 °C. That second column is the one that decides whether the part survives a hot corner, because ferrite loses saturation margin as it heats.

    Copper loss at the rated current works out to roughly 0.879 W from a typical DCR of 1.3 mOhm at 26 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    The core stores roughly 363 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    With K = 187, a peak-to-peak ripple of one amp produces roughly 104 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    The second saturation column, 28 A at 20% rolloff @ +125 °C, is the same core taken further into rolloff. The ratio between the two columns is a direct measure of how soft the curve is: a part with a wide gap between them loses inductance slowly and tolerates a larger transient peak.

    Where This Series Fits

    The HCF family is the ferrite option in the high-current range: lower core loss than a powder part at high frequency, with saturation current quoted at both +25 °C and +125 °C. It is the family for converters that run fast and hot.

    The HCF1007 family spans 0.3 uH to 10 uH; this row sits at position 3 of 12.

    Compared with its neighbours in the table, HCF1007-R68-R trades 0 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: ferrite core, 10.3 x 8.1 mm body at 6.65 mm.
    • Typical applications: voltage regulator modules (vrm); high current dc-dc converters; multi-phase buck regulators; servers and data networking; point-of-load modules.
    • Ferrite loses saturation margin as it heats. The +125 °C Isat column is the one that governs a hot design; the +25 °C figure is the optimistic one.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 1.3 mOhm becomes roughly 1.84 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the full-load inductance (FLL) is the value to use for ripple at rated current. OCL is the small-signal number; FLL is what the converter actually sees under load.

    • Check saturation at the +125 °C column when the enclosure runs hot.
    • Check the full-load inductance against the ripple target at maximum load.
    • Calculate ripple with FLL, not OCL: the loaded inductance is what the converter sees.

    Frequently Asked Questions

    Why are there two saturation currents?
    Ferrite loses saturation flux density as it heats. The +25 °C column describes a bench measurement; the +125 °C column describes the part under load in a hot enclosure, which is the one that governs the design.

    How is the K-factor used?
    Multiply K by the inductance in microhenry and by the peak-to-peak ripple in amps to get the flux swing the core sees. Read the core-loss curve at that amplitude and at your switching frequency.

    How is the K-factor used?
    Multiply K by the inductance in microhenry and by the peak-to-peak ripple in amps to get the flux swing the core sees. Read the core-loss curve at that amplitude and at your switching frequency.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products