Eaton HCM0503-1R5-R 1.5 uH Shielded Power Inductor
Eaton HCM0503-1R5-R 1.5 uH Shielded Power Inductor

Eaton HCM0503-1R5-R 1.5 uH Shielded Power Inductor

Share
Eaton HCM0503-1R5-R: molded high-current power inductor, 1.5 uH ±20%, 7.5 A Irms, Isat 7 A, DCR 17.1 mOhm, 5.5 x 5.3 mm.
    • Product Details
    • Download

    Eaton HCM0503-1R5-R 1.5 uH Shielded Power Inductor

    HCM0503-1R5-R at a glance: molded high-current power inductor, 1.5 uH ±20%, 7.5 A Irms, Isat 7 A (20% rolloff @ +25 °C), DCR 17.1 mOhm, 5.5 x 5.3 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM0503-1R5-R
    OCL (open circuit inductance)1.5 uH ±20%
    FLL minimum, at Isat0.96 uH
    Irms (DC, 40 °C rise)7.5 A
    Isat (20% rolloff @ +25 °C)7 A
    DCR typical @ +20 °C17.1 mOhm
    DCR maximum @ +20 °C18.5 mOhm
    K-factor (Bp-p = K x L x dI)393, Bp-p in Gauss
    Package5.5 x 5.3 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4430

    Outline Drawing

    HCM0503-1R5-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4430: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    Molded construction is what gives this family its mechanical robustness and its shielding. Because the core surrounds the winding on all sides, the leakage field that would otherwise couple into adjacent traces is small, and the part can be placed close to sensitive nodes.

    Copper loss at the rated current works out to roughly 0.962 W from a typical DCR of 17.1 mOhm at 7.5 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    Energy storage at the saturation current is around 36.8 uJ, the number that connects the inductance and the current rating into a single transient figure.

    The K-factor of 393 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 590 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    What This Family Is For

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    In the HCM0503 line-up this part is number 6 of 13 by inductance, between 0.2 uH and 22 uH.

    Compared with its neighbours in the table, HCM0503-2R2-R trades 3.3 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: iron powder core, 5.5 x 5.3 mm body at 3.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-load modules; desktop and server vrms and evrds; base station equipment; notebook and laptop regulators.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 18.5 mOhm becomes roughly 26.1 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Confirm the peak transient current stays under Isat with tolerance margin.
    • Build the thermal design on the maximum DCR, not the typical one.
    • Check the hot DCR before signing off the efficiency budget.

    Frequently Asked Questions

    How much does the inductance drop at rated current?
    That is what the Isat column quantifies. At the rated DC current the part is still inside the rolloff boundary, but the ripple calculation should use the FLL column rather than OCL.

    What makes a molded inductor different?
    The winding is pressed into the magnetic powder with no bobbin or air gap in the path. That is why the body is almost all magnetic material, the DCR is low for the size, and the part is mechanically robust.

    Is it magnetically shielded?
    Yes. The powder core surrounds the winding, so the leakage field is small and the part can sit close to sensitive traces without a shield can.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products