Eaton HCM0503-3R3-R 3.3 uH High-Current Inductor 36.4 mOhm
Eaton HCM0503-3R3-R 3.3 uH High-Current Inductor 36.4 mOhm

Eaton HCM0503-3R3-R 3.3 uH High-Current Inductor 36.4 mOhm

Share
Eaton HCM0503-3R3-R: molded high-current power inductor, 3.3 uH ±20%, 5.5 A Irms, Isat 6 A, DCR 36.4 mOhm, 5.5 x 5.3 mm.
    • Product Details
    • Download

    Eaton HCM0503-3R3-R 3.3 uH High-Current Inductor 36.4 mOhm

    HCM0503-3R3-R at a glance: molded high-current power inductor, 3.3 uH ±20%, 5.5 A Irms, Isat 6 A (20% rolloff @ +25 °C), DCR 36.4 mOhm, 5.5 x 5.3 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM0503-3R3-R
    OCL (open circuit inductance)3.3 uH ±20%
    FLL minimum, at Isat2.1 uH
    Irms (DC, 40 °C rise)5.5 A
    Isat (20% rolloff @ +25 °C)6 A
    DCR typical @ +20 °C36.4 mOhm
    DCR maximum @ +20 °C40.4 mOhm
    K-factor (Bp-p = K x L x dI)273, Bp-p in Gauss
    Package5.5 x 5.3 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4430

    Mechanical Drawing

    HCM0503-3R3-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4430: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    The part is a surface-mount molded inductor: powder core, directly wound and pressed, with the terminals formed from the winding ends. The absence of a bobbin or an air gap in the magnetic path is what keeps the DCR low for the current rating, and the soft saturation is a property of the distributed gap.

    At the rated 5.5 A the winding dissipates about 1.1 W in copper alone, using the typical DCR of 36.4 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    The core stores roughly 59.4 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    K-factor 273 means the flux swing is about 901 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    What This Family Is For

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    Within the HCM0503 family this is value 8 of 13, in a range that runs from 0.2 uH to 22 uH.

    Compared with its neighbours in the table, HCM0503-4R7-R trades 2.3 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: iron powder core, 5.5 x 5.3 mm body at 3.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-load modules; desktop and server vrms and evrds; base station equipment; notebook and laptop regulators.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 40.4 mOhm becomes roughly 57.1 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Verify the body height against the enclosure or heat-spreader clearance.
    • Build the thermal design on the maximum DCR, not the typical one.
    • Check the hot DCR before signing off the efficiency budget.

    Frequently Asked Questions

    Can two parts be stacked for higher current?
    Stacking halves the inductance and doubles the current capability in theory, but the two DCRs are not matched and the magnetic coupling is uncontrolled. Use a larger part instead.

    What makes a molded inductor different?
    The winding is pressed into the magnetic powder with no bobbin or air gap in the path. That is why the body is almost all magnetic material, the DCR is low for the size, and the part is mechanically robust.

    How much does the inductance drop at rated current?
    That is what the Isat column quantifies. At the rated DC current the part is still inside the rolloff boundary, but the ripple calculation should use the FLL column rather than OCL.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products