Eaton HCM0503-R35-R 0.35 uH Shielded Power Inductor

Eaton HCM0503-R35-R 0.35 uH Shielded Power Inductor

Share
Eaton HCM0503-R35-R: molded high-current power inductor, 0.35 uH ±20%, 16.6 A Irms, Isat 14.9 A, DCR 3.9 mOhm, 5.5 x 5.3 mm.
    • Product Details
    • Download

    Eaton HCM0503-R35-R 0.35 uH Shielded Power Inductor

    HCM0503-R35-R at a glance: molded high-current power inductor, 0.35 uH ±20%, 16.6 A Irms, Isat 14.9 A (20% rolloff @ +25 °C), DCR 3.9 mOhm, 5.5 x 5.3 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCM0503-R35-R
    OCL (open circuit inductance)0.35 uH ±20%
    FLL minimum, at Isat0.22 uH
    Irms (DC, 40 °C rise)16.6 A
    Isat (20% rolloff @ +25 °C)14.9 A
    DCR typical @ +20 °C3.9 mOhm
    DCR maximum @ +20 °C4.29 mOhm
    K-factor (Bp-p = K x L x dI)1,259, Bp-p in Gauss
    Package5.5 x 5.3 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4430

    Mechanical Dimensions & Pad Layout

    HCM0503-R35-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4430: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    This is one of the molded power inductors used across VRM, point-of-load and multiphase regulator designs. The family covers a wide inductance range in standard footprints, and every row is characterised for both typical and maximum DCR so the loss budget can be built either way.

    Copper loss at the rated current works out to roughly 1.07 W from a typical DCR of 3.9 mOhm at 16.6 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    The core stores roughly 38.9 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The K-factor of 1,259 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 441 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    What This Family Is For

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    The HCM0503 family spans 0.2 uH to 22 uH; this row sits at position 2 of 13.

    Compared with its neighbours in the table, HCM0503-R47-R trades 10.2 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: iron powder core, 5.5 x 5.3 mm body at 3.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-load modules; desktop and server vrms and evrds; base station equipment; notebook and laptop regulators.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 4.29 mOhm becomes roughly 6.06 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Check the hot DCR before signing off the efficiency budget.
    • Build the thermal design on the maximum DCR, not the typical one.
    • Build the thermal design on the maximum DCR, not the typical one.

    Frequently Asked Questions

    How much does the inductance drop at rated current?
    That is what the Isat column quantifies. At the rated DC current the part is still inside the rolloff boundary, but the ripple calculation should use the FLL column rather than OCL.

    Why quote typical and maximum DCR?
    A guaranteed thermal design uses the maximum. A nominal efficiency calculation uses the typical. Publishing both lets the same table serve either purpose.

    What makes a molded inductor different?
    The winding is pressed into the magnetic powder with no bobbin or air gap in the path. That is why the body is almost all magnetic material, the DCR is low for the size, and the part is mechanically robust.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products