Eaton HCM0503-R75-R 0.75 uH High-Current Inductor 8.5 mOhm
Eaton HCM0503-R75-R 0.75 uH High-Current Inductor 8.5 mOhm

Eaton HCM0503-R75-R 0.75 uH High-Current Inductor 8.5 mOhm

Share
Eaton HCM0503-R75-R: molded high-current power inductor, 0.75 uH ±20%, 11.3 A Irms, Isat 9.7 A, DCR 8.5 mOhm, 5.5 x 5.3 mm.
    • Product Details
    • Download

    Eaton HCM0503-R75-R 0.75 uH High-Current Inductor 8.5 mOhm

    HCM0503-R75-R at a glance: molded high-current power inductor, 0.75 uH ±20%, 11.3 A Irms, Isat 9.7 A (20% rolloff @ +25 °C), DCR 8.5 mOhm, 5.5 x 5.3 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM0503-R75-R
    OCL (open circuit inductance)0.75 uH ±20%
    FLL minimum, at Isat0.48 uH
    Irms (DC, 40 °C rise)11.3 A
    Isat (20% rolloff @ +25 °C)9.7 A
    DCR typical @ +20 °C8.5 mOhm
    DCR maximum @ +20 °C9.35 mOhm
    K-factor (Bp-p = K x L x dI)801, Bp-p in Gauss
    Package5.5 x 5.3 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4430

    Outline Drawing

    HCM0503-R75-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4430: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    The part is a surface-mount molded inductor: powder core, directly wound and pressed, with the terminals formed from the winding ends. The absence of a bobbin or an air gap in the magnetic path is what keeps the DCR low for the current rating, and the soft saturation is a property of the distributed gap.

    With 8.5 mOhm typical, the I-squared-R loss at the full 11.3 A rating is about 1.08 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Energy storage at the saturation current is around 35.3 uJ, the number that connects the inductance and the current rating into a single transient figure.

    With K = 801, a peak-to-peak ripple of one amp produces roughly 601 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Series Positioning

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    Of the 13 values listed for HCM0503, this is the 4th, in a family covering 0.2 uH to 22 uH.

    One step down the table, HCM0503-R47-R, sits at 0.47 uH with 12 A and 6.5 mOhm – the lower inductance buys about 1.9 A of extra current in the same body.

    • Core material: iron powder core, 5.5 x 5.3 mm body at 3.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-load modules; desktop and server vrms and evrds; base station equipment; notebook and laptop regulators.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Putting It to Work

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 9.35 mOhm becomes roughly 13.2 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Build the thermal design on the maximum DCR, not the typical one.
    • Verify the body height against the enclosure or heat-spreader clearance.
    • Verify the body height against the enclosure or heat-spreader clearance.

    Frequently Asked Questions

    What makes a molded inductor different?
    The winding is pressed into the magnetic powder with no bobbin or air gap in the path. That is why the body is almost all magnetic material, the DCR is low for the size, and the part is mechanically robust.

    How much inductance is left at rated current?
    That is what the saturation column describes. Isat is the peak current at which inductance has fallen by the stated percentage, so at the rated DC current the part is still inside that boundary.

    How much inductance is left at rated current?
    That is what the saturation column describes. Isat is the peak current at which inductance has fallen by the stated percentage, so at the rated DC current the part is still inside that boundary.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products