Eaton HCM0703-330-R 33 uH High-Current Inductor 220 mOhm
Eaton HCM0703-330-R 33 uH High-Current Inductor 220 mOhm

Eaton HCM0703-330-R 33 uH High-Current Inductor 220 mOhm

Share
Eaton HCM0703-330-R: molded high-current power inductor, 33 uH ±20%, 1.8 A Irms, Isat 2.2 A, DCR 220 mOhm, 7.4 x 6.8 mm.
    • Product Details
    • Download

    Eaton HCM0703-330-R 33 uH High-Current Inductor 220 mOhm

    HCM0703-330-R at a glance: molded high-current power inductor, 33 uH ±20%, 1.8 A Irms, Isat 2.2 A (20% rolloff @ +25 °C), DCR 220 mOhm, 7.4 x 6.8 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM0703-330-R
    OCL (open circuit inductance)33 uH ±20%
    FLL minimum, at Isat19.8 uH
    Irms (DC, 40 °C rise)1.8 A
    Isat (20% rolloff @ +25 °C)2.2 A
    DCR typical @ +20 °C220 mOhm
    DCR maximum @ +20 °C242 mOhm
    K-factor (Bp-p = K x L x dI)76, Bp-p in Gauss
    Package7.4 x 6.8 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4085

    Outline Drawing

    HCM0703-330-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4085: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    Molded construction is what gives this family its mechanical robustness and its shielding. Because the core surrounds the winding on all sides, the leakage field that would otherwise couple into adjacent traces is small, and the part can be placed close to sensitive nodes.

    The DCR figure of 220 mOhm is what sets the efficiency: at 1.8 A the winding drops about 0.396 mV and dissipates 0.713 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    Energy storage at the saturation current is around 79.9 uJ, the number that connects the inductance and the current rating into a single transient figure.

    The K-factor of 76 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 2,508 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Positioning in the Range

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    The HCM0703 family spans 0.15 uH to 33 uH; this row sits at position 16 of 16.

    The next value up in the same family, HCM0703-220-R, gives 22 uH at 2.3 A and DCR 135 mOhm: the extra inductance costs about 0 A of rated current.

    • Core material: iron powder core, 7.4 x 6.8 mm body at 3.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-loadmodules; desktop and server vrms and evrds; base station equipment; laptop and notebook regulators.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 242 mOhm becomes roughly 342 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Confirm the peak transient current stays under Isat with tolerance margin.
    • Confirm the shielding is adequate for the adjacent trace routing.
    • Allow for copper drift: resistance rises with temperature at roughly 0.4 % per °C.

    Frequently Asked Questions

    Is it magnetically shielded?
    Yes. The powder core surrounds the winding, so the leakage field is small and the part can sit close to sensitive traces without a shield can.

    Is it magnetically shielded?
    Yes. The powder core surrounds the winding, so the leakage field is small and the part can sit close to sensitive traces without a shield can.

    Is it magnetically shielded?
    Yes. The powder core surrounds the winding, so the leakage field is small and the part can sit close to sensitive traces without a shield can.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products