Eaton HCM0703-R15-R 0.15 uH Shielded Power Inductor
Eaton HCM0703-R15-R 0.15 uH Shielded Power Inductor

Eaton HCM0703-R15-R 0.15 uH Shielded Power Inductor

Share
Eaton HCM0703-R15-R: molded high-current power inductor, 0.15 uH ±20%, 26 A Irms, Isat 52 A, DCR 1.9 mOhm, 7.4 x 6.8 mm.
    • Product Details
    • Download

    Eaton HCM0703-R15-R 0.15 uH Shielded Power Inductor

    HCM0703-R15-R at a glance: molded high-current power inductor, 0.15 uH ±20%, 26 A Irms, Isat 52 A (20% rolloff @ +25 °C), DCR 1.9 mOhm, 7.4 x 6.8 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCM0703-R15-R
    OCL (open circuit inductance)0.15 uH ±20%
    FLL minimum, at Isat0.09 uH
    Irms (DC, 40 °C rise)26 A
    Isat (20% rolloff @ +25 °C)52 A
    DCR typical @ +20 °C1.9 mOhm
    DCR maximum @ +20 °C2.5 mOhm
    K-factor (Bp-p = K x L x dI)1,044, Bp-p in Gauss
    Package7.4 x 6.8 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4085

    Mechanical Drawing

    HCM0703-R15-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4085: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    The part is a surface-mount molded inductor: powder core, directly wound and pressed, with the terminals formed from the winding ends. The absence of a bobbin or an air gap in the magnetic path is what keeps the DCR low for the current rating, and the soft saturation is a property of the distributed gap.

    At the rated 26 A the winding dissipates about 1.28 W in copper alone, using the typical DCR of 1.9 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    The core stores roughly 203 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    With K = 1,044, a peak-to-peak ripple of one amp produces roughly 157 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Where This Series Fits

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    In the HCM0703 line-up this part is number 1 of 16 by inductance, between 0.15 uH and 33 uH.

    Compared with its neighbours in the table, HCM0703-R22-R trades 0 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: iron powder core, 7.4 x 6.8 mm body at 3.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-loadmodules; desktop and server vrms and evrds; base station equipment; laptop and notebook regulators.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 2.5 mOhm becomes roughly 3.53 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Verify the body height against the enclosure or heat-spreader clearance.
    • Verify the body height against the enclosure or heat-spreader clearance.
    • Confirm the peak transient current stays under Isat with tolerance margin.

    Frequently Asked Questions

    What makes a molded inductor different?
    The winding is pressed into the magnetic powder with no bobbin or air gap in the path. That is why the body is almost all magnetic material, the DCR is low for the size, and the part is mechanically robust.

    Why quote typical and maximum DCR?
    A guaranteed thermal design uses the maximum. A nominal efficiency calculation uses the typical. Publishing both lets the same table serve either purpose.

    Why quote typical and maximum DCR?
    A guaranteed thermal design uses the maximum. A nominal efficiency calculation uses the typical. Publishing both lets the same table serve either purpose.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products