Eaton HCM1305-2R2-R 2.20 uH High-Current Inductor 4.6 mOhm
Eaton HCM1305-2R2-R 2.20 uH High-Current Inductor 4.6 mOhm

Eaton HCM1305-2R2-R 2.20 uH High-Current Inductor 4.6 mOhm

Share
Eaton HCM1305-2R2-R: molded high-current power inductor, 2.20 uH ±20%, 20 A Irms, Isat 32 A, DCR 4.6 mOhm, 13.8 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCM1305-2R2-R 2.20 uH High-Current Inductor 4.6 mOhm

    HCM1305-2R2-R at a glance: molded high-current power inductor, 2.20 uH ±20%, 20 A Irms, Isat 32 A (20% rolloff @ +25 °C), DCR 4.6 mOhm, 13.8 x 12.5 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1305-2R2-R
    OCL (open circuit inductance)2.20 uH ±20%
    FLL minimum, at Isat1.41 uH
    Irms (DC, 40 °C rise)20 A
    Isat (20% rolloff @ +25 °C)32 A
    DCR typical @ +20 °C4.6 mOhm
    DCR maximum @ +20 °C5.29 mOhm
    K-factor (Bp-p = K x L x dI)191, Bp-p in Gauss
    Package13.8 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4371

    Outline Drawing

    HCM1305-2R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4371: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    The part is a surface-mount molded inductor: powder core, directly wound and pressed, with the terminals formed from the winding ends. The absence of a bobbin or an air gap in the magnetic path is what keeps the DCR low for the current rating, and the soft saturation is a property of the distributed gap.

    Copper loss at the rated current works out to roughly 1.84 W from a typical DCR of 4.6 mOhm at 20 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    At Isat the part holds about 1,126 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    The K-factor of 191 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 420 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    What This Family Is For

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    In the HCM1305 line-up this part is number 11 of 21 by inductance, between 0.1 uH and 33 uH.

    One step down the table, HCM1305-1R8-R, sits at 1.80 uH with 21 A and 4 mOhm – the lower inductance buys about 6 A of extra current in the same body.

    • Core material: iron powder core, 13.8 x 12.5 mm body at 5.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-load modules; desktop and server vrms and evrds; base station equipment; notebook and laptop regulators.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Design Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 5.29 mOhm becomes roughly 7.47 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Allow for copper drift: resistance rises with temperature at roughly 0.4 % per °C.
    • Allow for copper drift: resistance rises with temperature at roughly 0.4 % per °C.
    • Confirm the shielding is adequate for the adjacent trace routing.

    Frequently Asked Questions

    Can two parts be stacked for higher current?
    Stacking halves the inductance and doubles the current capability in theory, but the two DCRs are not matched and the magnetic coupling is uncontrolled. Use a larger part instead.

    How much does the inductance drop at rated current?
    That is what the Isat column quantifies. At the rated DC current the part is still inside the rolloff boundary, but the ripple calculation should use the FLL column rather than OCL.

    Is it magnetically shielded?
    Yes. The powder core surrounds the winding, so the leakage field is small and the part can sit close to sensitive traces without a shield can.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products