Eaton HCM1305-R82-R 0.82 uH High-Current Inductor 1.4 mOhm
Eaton HCM1305-R82-R 0.82 uH High-Current Inductor 1.4 mOhm

Eaton HCM1305-R82-R 0.82 uH High-Current Inductor 1.4 mOhm

Share
Eaton HCM1305-R82-R: molded high-current power inductor, 0.82 uH ±20%, 31 A Irms, Isat 53 A, DCR 1.4 mOhm, 13.8 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCM1305-R82-R 0.82 uH High-Current Inductor 1.4 mOhm

    HCM1305-R82-R at a glance: molded high-current power inductor, 0.82 uH ±20%, 31 A Irms, Isat 53 A (20% rolloff @ +25 °C), DCR 1.4 mOhm, 13.8 x 12.5 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCM1305-R82-R
    OCL (open circuit inductance)0.82 uH ±20%
    FLL minimum, at Isat0.52 uH
    Irms (DC, 40 °C rise)31 A
    Isat (20% rolloff @ +25 °C)53 A
    DCR typical @ +20 °C1.4 mOhm
    DCR maximum @ +20 °C1.61 mOhm
    K-factor (Bp-p = K x L x dI)358, Bp-p in Gauss
    Package13.8 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4371

    Mechanical Drawing

    HCM1305-R82-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4371: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    Molded construction is what gives this family its mechanical robustness and its shielding. Because the core surrounds the winding on all sides, the leakage field that would otherwise couple into adjacent traces is small, and the part can be placed close to sensitive nodes.

    The DCR figure of 1.4 mOhm is what sets the efficiency: at 31 A the winding drops about 0.043 mV and dissipates 1.34 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    The core stores roughly 1,152 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    K-factor 358 means the flux swing is about 294 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Series Positioning

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    Within the HCM1305 family this is value 7 of 21, in a range that runs from 0.1 uH to 33 uH.

    One step down the table, HCM1305-R68-R, sits at 0.68 uH with 34 A and 1.15 mOhm – the lower inductance buys about 5 A of extra current in the same body.

    • Core material: iron powder core, 13.8 x 12.5 mm body at 5.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-load modules; desktop and server vrms and evrds; base station equipment; notebook and laptop regulators.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Putting It to Work

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 1.61 mOhm becomes roughly 2.27 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Confirm the shielding is adequate for the adjacent trace routing.
    • Confirm the shielding is adequate for the adjacent trace routing.
    • Build the thermal design on the maximum DCR, not the typical one.

    Frequently Asked Questions

    What makes a molded inductor different?
    The winding is pressed into the magnetic powder with no bobbin or air gap in the path. That is why the body is almost all magnetic material, the DCR is low for the size, and the part is mechanically robust.

    Is it magnetically shielded?
    Yes. The powder core surrounds the winding, so the leakage field is small and the part can sit close to sensitive traces without a shield can.

    How much does the inductance drop at rated current?
    That is what the Isat column quantifies. At the rated DC current the part is still inside the rolloff boundary, but the ripple calculation should use the FLL column rather than OCL.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products