Eaton HCM1707-1R5-R 1.5 uH High-Current Inductor 1.85 mOhm
Eaton HCM1707-1R5-R 1.5 uH High-Current Inductor 1.85 mOhm

Eaton HCM1707-1R5-R 1.5 uH High-Current Inductor 1.85 mOhm

Share
Eaton HCM1707-1R5-R: molded high-current power inductor, 1.5 uH ±20%, 40 A Irms, Isat 40 A, DCR 1.85 mOhm, 17.5 x 17.2 mm.
    • Product Details
    • Download

    Eaton HCM1707-1R5-R 1.5 uH High-Current Inductor 1.85 mOhm

    HCM1707-1R5-R at a glance: molded high-current power inductor, 1.5 uH ±20%, 40 A Irms, Isat 40 A (20% rolloff @ +25 °C), DCR 1.85 mOhm, 17.5 x 17.2 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCM1707-1R5-R
    OCL (open circuit inductance)1.5 uH ±20%
    FLL minimum, at Isat0.96 uH
    Irms (DC, 40 °C rise)40 A
    Isat (20% rolloff @ +25 °C)40 A
    DCR typical @ +20 °C1.85 mOhm
    DCR maximum @ +20 °C2.15 mOhm
    K-factor (Bp-p = K x L x dI)124, Bp-p in Gauss
    Package17.5 x 17.2 mm
    Height7.0 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10295

    Mechanical Dimensions & Pad Layout

    HCM1707-1R5-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10295: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    A molded body around an alloy or iron powder core: the winding is pressed into the magnetic material, so the field is contained inside the part and the terminals come straight out of the molding. The result is a shielded inductor with a low profile and a soft saturation curve, on a footprint that is almost all magnetic material.

    Copper loss at the rated current works out to roughly 2.96 W from a typical DCR of 1.85 mOhm at 40 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    The core stores roughly 1,200 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    With K = 124, a peak-to-peak ripple of one amp produces roughly 186 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Where This Series Fits

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    The HCM1707 family spans 1.5 uH to 68 uH; this row sits at position 1 of 11.

    Compared with its neighbours in the table, HCM1707-2R2-R trades 0 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: iron powder core, 17.5 x 17.2 mm body at 7.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-load modules; desktop and server vrms and evrds; data networking and storage systems; base station equipment.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Putting It to Work

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 2.15 mOhm becomes roughly 3.04 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Confirm the peak transient current stays under Isat with tolerance margin.
    • Confirm the shielding is adequate for the adjacent trace routing.
    • Confirm the peak transient current stays under Isat with tolerance margin.

    Frequently Asked Questions

    What makes a molded inductor different?
    The winding is pressed into the magnetic powder with no bobbin or air gap in the path. That is why the body is almost all magnetic material, the DCR is low for the size, and the part is mechanically robust.

    How much does the inductance drop at rated current?
    That is what the Isat column quantifies. At the rated DC current the part is still inside the rolloff boundary, but the ripple calculation should use the FLL column rather than OCL.

    Why quote typical and maximum DCR?
    A guaranteed thermal design uses the maximum. A nominal efficiency calculation uses the typical. Publishing both lets the same table serve either purpose.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products