Eaton HCM1707-220-R Molded Inductor 22 uH, Isat 11 A
Eaton HCM1707-220-R Molded Inductor 22 uH, Isat 11 A

Eaton HCM1707-220-R Molded Inductor 22 uH, Isat 11 A

Share
Eaton HCM1707-220-R: molded high-current power inductor, 22 uH ±20%, 9.5 A Irms, Isat 11 A, DCR 21 mOhm, 17.5 x 17.2 mm.
    • Product Details
    • Download

    Eaton HCM1707-220-R Molded Inductor 22 uH, Isat 11 A

    HCM1707-220-R at a glance: molded high-current power inductor, 22 uH ±20%, 9.5 A Irms, Isat 11 A (20% rolloff @ +25 °C), DCR 21 mOhm, 17.5 x 17.2 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1707-220-R
    OCL (open circuit inductance)22 uH ±20%
    FLL minimum, at Isat14.1 uH
    Irms (DC, 40 °C rise)9.5 A
    Isat (20% rolloff @ +25 °C)11 A
    DCR typical @ +20 °C21 mOhm
    DCR maximum @ +20 °C23 mOhm
    K-factor (Bp-p = K x L x dI)37, Bp-p in Gauss
    Package17.5 x 17.2 mm
    Height7.0 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10295

    Mechanical Drawing

    HCM1707-220-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10295: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    Molded construction is what gives this family its mechanical robustness and its shielding. Because the core surrounds the winding on all sides, the leakage field that would otherwise couple into adjacent traces is small, and the part can be placed close to sensitive nodes.

    Copper loss at the rated current works out to roughly 1.9 W from a typical DCR of 21 mOhm at 9.5 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    The core stores roughly 1,331 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    With K = 37, a peak-to-peak ripple of one amp produces roughly 814 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    What This Family Is For

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    The HCM1707 family spans 1.5 uH to 68 uH; this row sits at position 8 of 11.

    One step down the table, HCM1707-150-R, sits at 15 uH with 12 A and 14.5 mOhm – the lower inductance buys about 3 A of extra current in the same body.

    • Core material: iron powder core, 17.5 x 17.2 mm body at 7.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-load modules; desktop and server vrms and evrds; data networking and storage systems; base station equipment.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 23 mOhm becomes roughly 32.5 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Check the hot DCR before signing off the efficiency budget.
    • Confirm the peak transient current stays under Isat with tolerance margin.
    • Confirm the peak transient current stays under Isat with tolerance margin.

    Frequently Asked Questions

    How much inductance is left at rated current?
    That is what the saturation column describes. Isat is the peak current at which inductance has fallen by the stated percentage, so at the rated DC current the part is still inside that boundary.

    How much does the inductance drop at rated current?
    That is what the Isat column quantifies. At the rated DC current the part is still inside the rolloff boundary, but the ripple calculation should use the FLL column rather than OCL.

    Why quote typical and maximum DCR?
    A guaranteed thermal design uses the maximum. A nominal efficiency calculation uses the typical. Publishing both lets the same table serve either purpose.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message