Eaton HCM1707-4R7-R 4.7 uH Shielded Power Inductor
Eaton HCM1707-4R7-R 4.7 uH Shielded Power Inductor

Eaton HCM1707-4R7-R 4.7 uH Shielded Power Inductor

Share
Eaton HCM1707-4R7-R: molded high-current power inductor, 4.7 uH ±20%, 27 A Irms, Isat 24 A, DCR 4.12 mOhm, 17.5 x 17.2 mm.
    • Product Details
    • Download

    Eaton HCM1707-4R7-R 4.7 uH Shielded Power Inductor

    HCM1707-4R7-R at a glance: molded high-current power inductor, 4.7 uH ±20%, 27 A Irms, Isat 24 A (20% rolloff @ +25 °C), DCR 4.12 mOhm, 17.5 x 17.2 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM1707-4R7-R
    OCL (open circuit inductance)4.7 uH ±20%
    FLL minimum, at Isat3.01 uH
    Irms (DC, 40 °C rise)27 A
    Isat (20% rolloff @ +25 °C)24 A
    DCR typical @ +20 °C4.12 mOhm
    DCR maximum @ +20 °C4.72 mOhm
    K-factor (Bp-p = K x L x dI)76, Bp-p in Gauss
    Package17.5 x 17.2 mm
    Height7.0 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10295

    Dimensions and Pad Layout

    HCM1707-4R7-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10295: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    The part is a surface-mount molded inductor: powder core, directly wound and pressed, with the terminals formed from the winding ends. The absence of a bobbin or an air gap in the magnetic path is what keeps the DCR low for the current rating, and the soft saturation is a property of the distributed gap.

    The DCR figure of 4.12 mOhm is what sets the efficiency: at 27 A the winding drops about 0.111 mV and dissipates 3 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    At Isat the part holds about 1,354 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    K-factor 76 means the flux swing is about 357 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Series Positioning

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    Of the 11 values listed for HCM1707, this is the 3th, in a family covering 1.5 uH to 68 uH.

    The next value up in the same family, HCM1707-6R8-R, gives 6.8 uH at 20 A and DCR 6.55 mOhm: the extra inductance costs about 17 A of rated current.

    • Core material: iron powder core, 17.5 x 17.2 mm body at 7.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-load modules; desktop and server vrms and evrds; data networking and storage systems; base station equipment.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 4.72 mOhm becomes roughly 6.67 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Confirm the shielding is adequate for the adjacent trace routing.
    • Allow for copper drift: resistance rises with temperature at roughly 0.4 % per °C.
    • Check the hot DCR before signing off the efficiency budget.

    Frequently Asked Questions

    How much does the inductance drop at rated current?
    That is what the Isat column quantifies. At the rated DC current the part is still inside the rolloff boundary, but the ripple calculation should use the FLL column rather than OCL.

    How much inductance is left at rated current?
    That is what the saturation column describes. Isat is the peak current at which inductance has fallen by the stated percentage, so at the rated DC current the part is still inside that boundary.

    Can two parts be stacked for higher current?
    Stacking halves the inductance and doubles the current capability in theory, but the two DCRs are not matched and the magnetic coupling is uncontrolled. Use a larger part instead.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products