Eaton HCM1A0503-3R3-R AEC-Q200 Inductor 3.3 uH, Isat 5.6 A
Eaton HCM1A0503-3R3-R AEC-Q200 Inductor 3.3 uH, Isat 5.6 A

Eaton HCM1A0503-3R3-R AEC-Q200 Inductor 3.3 uH, Isat 5.6 A

Share
Eaton HCM1A0503-3R3-R: AEC-Q200 automotive power inductor, 3.3 uH ±20%, 3.8 A Irms, Isat 5.6 A, DCR 36.4 mOhm, 5.5 x 5.3 mm.
    • Product Details
    • Download

    Eaton HCM1A0503-3R3-R AEC-Q200 Inductor 3.3 uH, Isat 5.6 A

    HCM1A0503-3R3-R at a glance: AEC-Q200 automotive power inductor, 3.3 uH ±20%, 3.8 A Irms, Isat 5.6 A (20% rolloff @ +25 °C), DCR 36.4 mOhm, 5.5 x 5.3 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A0503-3R3-R
    OCL (open circuit inductance)3.3 uH ±20%
    FLL minimum, at Isat2.1 uH
    Irms (DC, 40 °C rise)3.8 A
    Isat (20% rolloff @ +25 °C)5.6 A
    DCR typical @ +20 °C36.4 mOhm
    DCR maximum @ +20 °C40.4 mOhm
    K-factor (Bp-p = K x L x dI)332, Bp-p in Gauss
    Package5.5 x 5.3 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10547

    Outline Drawing

    HCM1A0503-3R3-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10547: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    With 36.4 mOhm typical, the I-squared-R loss at the full 3.8 A rating is about 0.526 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    At Isat the part holds about 51.7 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    The K-factor of 332 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 1,096 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 15 values listed for HCM1A0503, this is the 11th, in a family covering 0.2 uH to 10 uH.

    Compared with its neighbours in the table, HCM1A0503-4R7-R trades 1.4 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 5.5 x 5.3 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 40.4 mOhm becomes roughly 61.8 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the qualification and the mounting process match the assembly line.
    • Verify the qualification and the mounting process match the assembly line.
    • Verify the part marking for revision traceability in production.

    Frequently Asked Questions

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products